Add Minewsemi ME25LS01 variant

src/helpers/nrf52/MinewsemiME25LS01Board.h

@@ -0,0 +1,112 @@
+#pragma once
+
+#include <MeshCore.h>
+#include <Arduino.h>
+
+// LoRa and SPI pins
+
+#define  P_LORA_DIO_1   (32 + 12)  // P1.12
+#define  P_LORA_NSS     (32 + 13)  // P1.13
+#define  P_LORA_RESET   (32 + 11)  // P1.11
+#define  P_LORA_BUSY    (32 + 10)  // P1.10
+#define  P_LORA_SCLK    (32 + 15)  // P1.15
+#define  P_LORA_MISO    (0 + 29)   // P0.29
+#define  P_LORA_MOSI    (0 + 2)    // P0.2
+ 
+#define LR11X0_DIO_AS_RF_SWITCH  true
+#define LR11X0_DIO3_TCXO_VOLTAGE   1.6
+
+// built-ins
+//#define  PIN_VBAT_READ    5
+//#define  ADC_MULTIPLIER   (3 * 1.73 * 1000)
+
+class MinewsemiME25LS01Board : public mesh::MainBoard {
+protected:
+  uint8_t startup_reason;
+  uint8_t btn_prev_state;
+
+public:
+  void begin();
+
+  uint16_t getBattMilliVolts() override {
+  #ifdef BATTERY_PIN
+   #ifdef PIN_3V3_EN
+    digitalWrite(PIN_3V3_EN, HIGH);
+   #endif
+    analogReference(AR_INTERNAL_3_0);
+    analogReadResolution(12);
+    delay(10);
+    float volts = (analogRead(BATTERY_PIN) * ADC_MULTIPLIER * AREF_VOLTAGE) / 4096;
+   #ifdef PIN_3V3_EN
+    digitalWrite(PIN_3V3_EN, LOW);
+   #endif
+
+    analogReference(AR_DEFAULT);  // put back to default
+    analogReadResolution(10);
+
+    return volts * 1000;
+  #else
+    return 0;
+  #endif
+  }
+
+  uint8_t getStartupReason() const override { return startup_reason; }
+
+  const char* getManufacturerName() const override {
+    return "m25ls01";
+  }
+
+  int buttonStateChanged() {
+  #ifdef BUTTON_PIN
+    uint8_t v = digitalRead(BUTTON_PIN);
+    if (v != btn_prev_state) {
+      btn_prev_state = v;
+      return (v == LOW) ? 1 : -1;
+    }
+  #endif
+    return 0;
+  }
+
+  void powerOff() override {
+    #ifdef HAS_GPS
+        digitalWrite(GPS_VRTC_EN, LOW);
+        digitalWrite(GPS_RESET, LOW);
+        digitalWrite(GPS_SLEEP_INT, LOW);
+        digitalWrite(GPS_RTC_INT, LOW);
+        pinMode(GPS_RESETB, OUTPUT);
+        digitalWrite(GPS_RESETB, LOW);
+    #endif
+    
+    #ifdef BUZZER_EN
+        digitalWrite(BUZZER_EN, LOW);
+    #endif
+    
+    #ifdef PIN_3V3_EN
+        digitalWrite(PIN_3V3_EN, LOW);
+    #endif
+
+    #ifdef LED_PIN
+    digitalWrite(LED_PIN, LOW);
+    #endif
+    #ifdef BUTTON_PIN
+    nrf_gpio_cfg_sense_input(digitalPinToInterrupt(BUTTON_PIN), NRF_GPIO_PIN_PULLUP, NRF_GPIO_PIN_SENSE_HIGH);
+    #endif
+    sd_power_system_off();
+  }
+
+  #if defined(P_LORA_TX_LED)
+  void onBeforeTransmit() override {
+    digitalWrite(P_LORA_TX_LED, HIGH);// turn TX LED on
+  }
+  void onAfterTransmit() override {
+    digitalWrite(P_LORA_TX_LED, LOW); // turn TX LED off
+  }
+#endif
+
+
+  void reboot() override {
+    NVIC_SystemReset();
+  }
+
+//  bool startOTAUpdate(const char* id, char reply[]) override;
+};