Merge remote-tracking branch 'upstream/dev' into 2026/remote-lna

variants/heltec_v4/HeltecV4Board.cpp

@@ -7,19 +7,26 @@ void HeltecV4Board::begin() {
     pinMode(PIN_ADC_CTRL, OUTPUT);
     digitalWrite(PIN_ADC_CTRL, LOW); // Initially inactive
 
+    // Set up digital GPIO registers before releasing RTC hold. The hold latches
+    // the pad state including function select, so register writes accumulate
+    // without affecting the pad. On hold release, all changes apply atomically
+    // (IO MUX switches to digital GPIO with output already HIGH — no glitch).
     pinMode(P_LORA_PA_POWER, OUTPUT);
     digitalWrite(P_LORA_PA_POWER,HIGH);
+    rtc_gpio_hold_dis((gpio_num_t)P_LORA_PA_POWER);
 
-    rtc_gpio_hold_dis((gpio_num_t)P_LORA_PA_EN);
     pinMode(P_LORA_PA_EN, OUTPUT);
     digitalWrite(P_LORA_PA_EN,HIGH);
+    rtc_gpio_hold_dis((gpio_num_t)P_LORA_PA_EN);
     pinMode(P_LORA_PA_TX_EN, OUTPUT);
     digitalWrite(P_LORA_PA_TX_EN,LOW);
 
+    esp_reset_reason_t reason = esp_reset_reason();
+    if (reason != ESP_RST_DEEPSLEEP) {
+      delay(1);  // GC1109 startup time after cold power-on
+    }
 
     periph_power.begin();
-
-    esp_reset_reason_t reason = esp_reset_reason();
     if (reason == ESP_RST_DEEPSLEEP) {
       long wakeup_source = esp_sleep_get_ext1_wakeup_status();
       if (wakeup_source & (1 << P_LORA_DIO_1)) {  // received a LoRa packet (while in deep sleep)
@@ -50,7 +57,9 @@ void HeltecV4Board::begin() {
 
     rtc_gpio_hold_en((gpio_num_t)P_LORA_NSS);
 
-    rtc_gpio_hold_en((gpio_num_t)P_LORA_PA_EN); //It also needs to be enabled in receive mode
+    // Hold GC1109 FEM pins during sleep to keep LNA active for RX wake
+    rtc_gpio_hold_en((gpio_num_t)P_LORA_PA_POWER);
+    rtc_gpio_hold_en((gpio_num_t)P_LORA_PA_EN);
 
     if (pin_wake_btn < 0) {
       esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1), ESP_EXT1_WAKEUP_ANY_HIGH);  // wake up on: recv LoRa packet

variants/heltec_v4/platformio.ini

@@ -23,7 +23,7 @@ build_flags =
   -D P_LORA_PA_TX_EN=46  ; PA CPS - GC1109 TX PA full(High) / bypass(Low)
   -D PIN_USER_BTN=0
   -D PIN_VEXT_EN=36
-  -D PIN_VEXT_EN_ACTIVE=LOW
+  -D PIN_VEXT_EN_ACTIVE=HIGH
   -D LORA_TX_POWER=10 ;If it is configured as 10 here, the final output will be 22 dbm.
   -D MAX_LORA_TX_POWER=22 ; Max SX1262 output
   -D SX126X_REGISTER_PATCH=1       ; Patch register 0x8B5 for improved RX
@@ -55,8 +55,6 @@ build_flags =
   -D PIN_BOARD_SDA=17
   -D PIN_BOARD_SCL=18
   -D PIN_OLED_RESET=21
-  -D ENV_PIN_SDA=4
-  -D ENV_PIN_SCL=3
 build_src_filter= ${Heltec_lora32_v4.build_src_filter}
 lib_deps = ${Heltec_lora32_v4.lib_deps}
 

variants/heltec_v4/target.cpp

@@ -24,7 +24,7 @@ AutoDiscoverRTCClock rtc_clock(fallback_clock);
 #endif
 
 #ifdef DISPLAY_CLASS
-  DISPLAY_CLASS display(&(board.periph_power));
+  DISPLAY_CLASS display(NULL);
   MomentaryButton user_btn(PIN_USER_BTN, 1000, true);
 #endif