Merge branch 'dev' into cli-lna-command

docs/cli_commands.md

@@ -219,20 +219,6 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 ---
 
-#### View or change the boosted receive gain mode
-**Usage:**
-- `get radio.rxgain`
-- `set radio.rxgain <state>`
-
-**Parameters:**
-- `state`: `on`|`off`
-
-**Default:** `off`
-
-**Note:** Only available on SX1262 and SX1268 based boards.
-
----
-
 #### Change the radio parameters for a set duration
 **Usage:** 
 - `tempradio <freq>,<bw>,<sf>,<cr>,<timeout_mins>`
@@ -263,7 +249,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 ---
 
-#### View or change this node's rx boosted gain mode (SX12xx only, v1.14.1+)
+#### View or change this node's rx boosted gain mode (SX12xx and LR1110, v1.14.1+)
 **Usage:**
 - `get radio.rxgain`
 - `set radio.rxgain <state>`
@@ -396,7 +382,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 **Note:** `|` characters are translated to newlines
 
-**Note:** Requires firmware 1.12.+
+**Note:** Requires firmware 1.12+
 
 ---
 
@@ -419,6 +405,11 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 ---
 
+#### View this node's firmware version
+**Usage:** `ver`
+
+---
+
 #### View this node's configured role
 **Usage:** `get role`
 
@@ -434,7 +425,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 - `on`: enable power saving
 - `off`: disable power saving
 
-**Default:** `on`
+**Default:** `off`
 
 **Note:** When enabled, device enters sleep mode between radio transmissions
 
@@ -488,7 +479,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
   
 **Default:** `off`
 
-**Note:** When it is enabled, repeaters will now reject flood packets which look like they are in a loop. This has been happening recently in some meshes when there is just a single 'bad' repeater firmware out there (prob some forked or custom firmware). If the payload is messed with, then forwarded, the same packet ends up causing a packet storm, repeated up to the max 64 hops. This feature was added in firmware 1.14
+**Note:** When it is enabled, repeaters will now reject flood packets which look like they are in a loop. This has been happening recently in some meshes when there is just a single 'bad' repeater firmware out there (probably some forked or custom firmware). If the payload is messed with, then forwarded, the same packet ends up causing a packet storm, repeated up to the max 64 hops. This feature was added in firmware 1.14
 
 **Example:** If preference is `loop.detect minimal`, and a 1-byte path size packet is received, the repeater will see if its own ID/hash is already in the path. If it's already encoded 4 times, it will reject the packet.  If the packet uses 2-byte path size, and repeater's own ID/hash is already encoded 2 times, it rejects. If the packet uses 3-byte path size, and the repeater's own ID/hash is already encoded 1 time, it rejects. 
 
@@ -645,6 +636,21 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 **Default:** `64`
 
+---
+
+#### Limit the number of hops for an unscoped flood message
+**Usage:**
+- `get flood.max.unscoped`
+- `set flood.max.unscoped <value>`
+
+**Parameters:**
+- `value`: Maximum flood hop count (0-64) for a packet without a scope (no region set)
+
+**Default:** `0xFF` - indicates it hasn't been set, will track flood.max until it is.
+
+**Note:** An alternative to `region denyf *`, setting `flood.max.unscoped` to a lower value such as `3` would allow for local unscoped messages to propagate, while preventing noisy neighbors from flooding a local region.
+
+
 ---
 
 ### ACL
@@ -770,6 +776,47 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 
 ---
 
+#### Define region hierarchy (single line)
+**Usage:**
+- `region def <token> [<token> ...]`
+
+**Parameters (tokens):** Space-separated. A logical **cursor** starts at the wildcard `*`.
+
+- **`name`** — Create `name` as a child of the current cursor (equivalent to `region put name` with the cursor as parent). Cursor moves to `name`.
+- **`name|jump`** *(or `name,jump`)* — Create `name` as a child of the current cursor, then move the cursor to `jump` (must already exist on the node, or have been created earlier in this command). `jump` is **not** the parent of `name`; use this form to pop back up and start another branch.
+
+**Behavior:** Each created region defaults to flood-allowed (same as `region put`). The reply is the resulting region tree (same format as bare `region`); review it before running `region save` to persist. On error, the reply is `Err - ...` and any regions placed before the failure remain on the node, just like a partial chain of `region put`.
+
+**Existing regions:** `region def` does not clear the existing tree — if a name already exists, its parent is updated to the current cursor; otherwise a new region is created. To start from scratch, `region remove` the unwanted regions first.
+
+**Limits:** Repeater serial accepts one line up to **160 characters**. For larger trees, split across multiple `region def` commands; the cursor resets to `*` between commands, so lead the next command with `child|ancestor` to reposition. Each token splits at most once on `|` — `region def a|b|c|d` is not a flat-list shorthand; see the flat-list example below.
+
+**Example — linear chain** (each token becomes a child of the previous):
+```
+region def a b c d e
+region save
+```
+
+**Example — branched tree** (equivalent to `region put a`, `region put b a`, `region put c b`, `region put d c`, `region put e b`, `region put f e`):
+```
+region def a b c d|b e f
+region save
+```
+
+**Example — error and partial state:**
+```
+region def a b c|nope d
+```
+The reply is `Err - unknown jump: nope`. `a`, `b`, and `c` were placed before the failure; `d` was not. Run `region` to inspect, then re-run with a corrected jump or repair with `region remove` / `region put`.
+
+**Example — flat list** (each region a child of `*`). Use `|*` after each token to pop the cursor back to the root before the next token:
+```
+region def a|* b|* c|* d|* e|* f
+region save
+```
+
+---
+
 #### Remove a region
 **Usage:** 
 - `region remove <name>`
@@ -790,7 +837,7 @@ This document provides an overview of CLI commands that can be sent to MeshCore
 **Parameters:**
 - `filter`: `allowed`|`denied`
 
-**Note:** Requires firmware 1.12.+
+**Note:** Requires firmware 1.12+
 
 ---