Duplicates found between the L1 and L2 frontends, and inside the L2 one:
- geo::fmtLocShare / fmtLatLon / turnDeg / isAhead (GeoUtils.h): the [LOC]
text was built in five places, the turn angle and its "ahead" threshold in
both navigations, coordinates by hand in nine. Tested.
- LiveShareEngine::setEnabled: live share was switched in three places.
- L1 waypoint share uses WaypointModel::shareText; Trail's "Share my pos"
goes through UITask::quickShareMyLocation, so it now sends to a running
live-share session as the home Map page does.
- L2 Widgets.h: switchCreate (one switch size, was four), switchRow with a
state and callback (16 hand-wired copies), switchRowOpens (Bluetooth, WiFi,
GPS), primaryButton (one height for Save / Measure / New area / Update).
GPS: with it off, starting the trail, live share or track back, sharing or
marking a position, or centring the map asks first ("GPS is off") on both
L1 and L2; Cancel leaves it undone. A share or a mark waits for a fresh fix
(a switched-off module may still report its last one), which also fixes the
L1 "Share my pos" sending a stale position. SOS still turns the GPS on itself.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Settings: Name and Radio first, then Bluetooth, WiFi and GPS side by side
(a tap on each row opens its details: the pairing PIN, the networks, the GPS
screen with a new Options tab for power saving and the fixed position), then
Device, Mesh & data (Adverts & privacy now holds Auto-advert) and System.
Time & units, Power as one group. Row symbols get a column of their own, value
labels are as wide as their text, group headings are uppercase everywhere, the
auto-add node types show only with "By type". SOS in three groups, WiFi with
its switch, Map tools with the layers (Packet flow among them) under the trail.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
An arrow at the target on a round dial whose top is the way you're heading:
turn until it points up. It turns green and the ring doubles when you're
within 12 degrees. The text says how far to turn ("turn right 55") instead of
two bearings to subtract. Standing still there's no course: the arrow greys
out, the top is north and marked red, and the text keeps the bearing.
sim_nav_target() sets a target from the simulator page.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Map tools > Layers > Map picks what the map is drawn from:
- Topo: OpenTopoMap, as before.
- Light and Dark: Esri's grey canvases, no labels, up to z16.
- Satellite: Esri World Imagery.
- Esri Topo.
Each layer has its own folder for downloaded areas (/sdcard/maps-light,
-dark, -sat, -esritopo; Topo stays in /sdcard/maps) and its own live-tile
cache. Live-cache records carry the layer.
Esri serves JPEG: decoded with LVGL's tjpgd (LV_USE_TJPGD), whatever the
file name says. The layer is kept in NVS (mc_ui/layer); switching waits
while a download or a deletion runs in the current folder.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
WiFi starts and joins on internal RAM: ~42 KB the first time, ~25 KB after,
more for WPA. Free internal RAM had shrunk to ~20 KB after opening the map
(the tile decoder's 12 KB stack, the 32 KB I-cache, the DMA draw buffers,
UI statics), so a scan failed at once (esp_wifi_init: no memory) and a join
during a tile download timed out (AUTH_EXPIRE).
- ESP-IDF: CONFIG_SPIRAM_ALLOW_BSS_SEG_EXTERNAL_MEMORY, and the esp_timer
task stack 8 -> 4 KB (it uses ~0.4 KB). Rebuild the framework libs:
pio run -e Wio_Tracker_L2_idf_libs.
- PSRAM_BSS (EXT_RAM_BSS_ATTR) on the UI's big statics: QR codes, map
state, charts, lists. .dram0.bss 115 -> 66 KB.
- The tile decoder's and fetcher's task stacks in PSRAM.
Free internal RAM, idle: 48 -> 105 KB; WiFi up: 57 KB, 29 KB at the
lowest while downloading tiles.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Density from less chrome instead of smaller rows (ROW_H stays 44):
- titled screens drop the status bar; the title bar (APPBAR_H) holds back,
the title, the screen's actions and the time/battery on a pill; the status
bar returns for Home, the map, typing, the quick panel and the lock
- one radius (RADIUS) for everything tapped: buttons, tabs, choices, chips
- tabs are all segmented at TAB_H in the body (GPS, Clock converted)
- Nodes: chips row + sort + status line become one toolbar row with
Show / Order choices; Messages' All/Favourites is the same choice
- nav map: the target bar only while there is a target; the pin opens one
"Places" popup; back from a map options page restores the map and Map
tools as left, without a jump
- node detail actions at the top of the scroll; Home tiles fill the page
- rowsFit() leaves growing labels to the flex (a screen title cut to one
letter after Messages' filter changed)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Core: PathEditor (UiCore::route) loads, edits, traces and saves the route to
a contact; MyMesh::sendTrace over an explicit route with per-hop SNRs,
setContactPath / setContactPinned. A route can be kept
(CONTACT_FLAG_ROUTE_PINNED, ContactInfo::flags bit 4): a path heard from the
node doesn't replace it and the last DM resend doesn't drop it.
ui-lvgl: Route screen (node detail), repeater picker by distance, picking
hops by tapping the nodes map (numbered badges, line, Undo / Done). The
map's markers are one drawn layer with hit-testing and name decluttering
instead of three objects per node.
ui-new: Path / trace view in the Nodes action menu; Add reuses the list
filtered to repeaters.
First cut: built for L2 LVGL, L1 OLED and L1 e-ink, tried on L2 only.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
- L2 vector packs: a damaged count can't wrap the index size, and an
entry pointing past the file is refused.
- L2 map share-target list: sized for 40 long channel names and 16
favourites (it could overflow), off the stack.
- L2 SD history: a file with an unreadable header is set aside as .bad
instead of written over; Delete message history takes those too.
- Contact lookups by key or hash start after the reserved anon slots (an
empty one matched a 00 hop hash with a blank name); MessagesScreen uses
contactctl::hopName().
- Nearby keeps its selection by public key: deleting a contact shifts
the table.
- ui-new Live Share target cycle holds every channel and favourite.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Chart.h draws Diagnostics > History, the noise sweep and the trail's height
profile: round values up the left, labels along the bottom, a solid fill
(no transparency) and, under a finger, the sample's value and when / where.
Sim: sim_open("histdemo") / ("profdemo") fill them with made-up data.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- ui-lvgl: navTextEntry()/TextEntry replace eight copies of popup + field +
keyboard wiring; one byte-capped insert callback instead of two.
- ui-new: drawHeadedBubble()/BubbleMark replace the duplicated DM and channel
bubble drawing in MessagesScreen.
- GpsSky::halt(): stopping the receiver ends an unfinished search but keeps
the first-fix time; keyboard cursor blink restarts after a key.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01VeBrxKyHHxWsmttVkUdBrj
Node detail: a card with a compass rose and the hop chain over the info;
the bar keeps Message / Admin / Add, Ping and Navigate, the rest goes to a
"More" group under the info (favourite toggled in place, delete by a second
tap). Nodes: an arrow by each distance. A trail's height profile in Map
tools and a saved trail's popup. Diagnostics > History: battery, noise,
SNR and traffic charts. Clock > Calendar: today, the weekend and alarm days.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Each point keeps the GPS altitude in what was padding, so a point stays
16 bytes. The save format goes to version 2; version 1 files still load,
with the altitude unknown. GPX export writes <ele>.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- ui-core: Diagnostics::systemLines, NearbyModel::typeShort,
rptctl::currentPresetName, RoomSessions::pendingKey, settings::isSwitch,
UiCore::reconcileDMUnread.
- ui-new: the retired Recent page, fmtAlt, the battMvToPercent wrapper,
setFavouriteChannelSlot, AccordionList onHeader/visibleCount, drawBoxedIcon
and seven unused icons; info::row folded into info::valueRow.
- ui-lvgl: onOpenNav, TileDownloader::withTrails; the trail header size is
one constant (TRAIL_HDR) for live and saved trails.
- Home quick panels save prefs only when a value changed.
- Comments brought in line with the code (status bar reserve, settings rows,
page order, SH1106 frame skip, UiCore header).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Recording / live share and the download stack in a column at the top
centre, empty when nothing runs; the recording pill is plain text with
only its mark coloured (red stop, accent pause / live) -- all-red text
was hard to read over the map. The credit, scale bar and zoom share one
pill bottom left (a tap shows the credit). Every map pill is 22 px with
round ends.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The vector map isn't finished: without the flag it stays off whatever
was saved, and its switch and the Vector regions row are gone from the
map tools. The code stays.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Found by counting flushes on idle screens in the sim:
- The compose field's cursor blinked (a redraw every 400 ms) as soon as
a conversation opened, the keyboard hidden: lv_keyboard_set_textarea()
focuses the field, and LVGL only stops a blink when the cursor moves.
fieldFocus() sets the state and nudges the blink; also used for the
WiFi and channel fields, which left theirs running.
- lv_obj_align_to() restyles on every call, so the status bar's icons
redrew every second; placeLeftOf() moves them only when they move.
- Text colours set every second (nav bar, GPS status, Diag errors) go
through setTextColor(), which skips an unchanged colour.
- A LV_LABEL_LONG_DOT label writes its "..." into its own text, so
setText() never matched and rewrote it every refresh (the nav bar's
hint); labelShows() reads past the dots.
- The map area, the area-outline, trail and vector-label layers were
invalidated on every map refresh (every 3 s, a full-map redraw); now
only when the view or what they draw changed.
Idle map: 17 -> 1 flush in 5 s; list and settings screens: 0.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Measured on the L2 (steady full frames): Settings page 37.7 -> 31.4 ms,
Display 41.5 -> 37.9, Contacts 34.6 -> 32.9, Home 37.3 -> 32.4.
- styleSurface() leaves boxes in the page colour unpainted; styleOpaque()
for the screen and the status bar, which things slide under.
- group() cards clip their corners only while a row is held
(rowPressable(), shared by the tappable rows).
- rowSlider(): the track an opaque tint (theme::mix(), also behind
ACCENT_DIM) instead of 20 % accent blended every frame.
- Map buttons, pills, scale, nav bar and the Home minimap labels opaque.
- Screens drift in without the fading cover: its full-screen blend was in
every entrance frame (page 39 -> 29 ms).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Trail on the L2: 32768 points every 5 m, no simplification, no point
spacing setting; copied to the card every minute and restored at power-on.
The line keeps up with the position dot (incremental sync, pending point).
Map: a tap's finger jitter no longer turns follow off; the GPS button
shows when the map follows. The trail is drawn as one polyline with
breaks and off-view chunks skipped (an lv_line queued a draw task per
point).
Fewer rebuilds: conversation bubbles patched (new messages, delivery
marks), home mini-map dots reused, Nearby rows rewritten in place,
history read in runs and each file opened once.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- CPU at 80 MHz with the screen on after 2 s without touch or animation;
a touch restores the full clock before its frame is drawn
- setText(): periodic refreshes no longer redraw unchanged labels
(status bar, Home, lock, Diag, GPS, compass, clock, map, nav, nearby)
- map markers kept across the 3 s rebuild when unchanged
- app connected: the loop blocks until a BLE frame arrives
(serialFrameArrived / hasPendingFrames) instead of polling every 2 ms
- PSRAM: boot frame sprite and the HTTP response buffer released
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Dead code gone: anim::fadeHide, radioctl::presetCount, the L2 board's
setSdPower / setGrovePower / expanderOK (awRead, gnssReset now private).
- buttonBar() / barButton() replace 7 copies of the popup button row.
- confirmBody(): one red-button confirm for reboot / power off, reset
counters, admin commands, preset and scope delete.
- tapConfirmed(): the 11 "tap again" buttons share one mechanism, 3 s
everywhere, the label restored when left alone.
- noteLabel() for ~30 wrapped notes.
- localTm() in NodePrefs.h and one MONTHS table: lvgl, MsgExpand, the L1
clock and lock screen.
- The sim keeps UI settings in an in-memory nvs::, so one set of load /
save helpers serves both.
- Asleep, the loop wakes every 50 ms (the button / touch poll), not 20.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Map tools: TRAIL, LIVE SHARE and ARRIVAL ALERT each with their own options
page (that section of Map options; back returns to Map tools), the arrival
alert switch where its state is shown, OFFLINE MAPS (Map areas, Live
tiles; the separate Download an area is gone -- a running or unfinished
download shows at the top of Map areas) and LAYERS.
Map areas: picking one frames it on the map above a small sheet (no Show
button, the map above isn't dimmed); closing the sheet, however it's
closed, puts the map back where it was and drops the outline -- it used
to stay on the map. New popup kind POP_BOTTOM.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Every toggle / stepper wrote the prefs file straight away (0.1-0.6 s on the
ESP32's SPIFFS), which stuttered the UI and wore the flash. prefsSave() now
only marks them dirty; they're written once when the screen is left, when the
display goes off, or after 60 s at the latest -- the L1's approach. Shutdown
and the pre-restart OTA save still write immediately.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
LVGL 9.2.2 measures a SIZE_CONTENT box from its children as scrolled, so an
elastic pull past the end of a capped popup list shrank it by the overshoot,
again on every pull. lvgl_patches.py fixes calc_content_height in the
downloaded library (a build middleware for PlatformIO, called directly by the
sim's build_wasm.sh).
The five popups that each built the same panel now share popupOpen() (fit to
content / full height / under the status bar).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
One .vpk file per region in /vmap (header, sorted index of tiles and
points, then the data), read in place with the index in PSRAM; loose
{dz}/{x}/{y}.vt/.vp files still work. osm_vector.py writes packs
(--pack/--name), reads OSM PBF extracts for a box (--pbf/--bbox, via
pyosmium) and picks label languages (--lang). Map tools > Vector regions
lists the packs on the card: show one on the map, delete it. No
on-device download: packs are made with the tool.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
tools/maps/osm_vector.py turns Overpass JSON into VT2 tiles (data zooms
10/12/14, per-feature bbox, simplified); VectorTileProvider draws them
into 256 px tiles (scanline polygons, thick lines with round joins) with
a small PSRAM cache of data files. Behind Map tools > Vector map (test),
raster where there is no vector data.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Download an area: a frame with four corner handles on the map (kept in
world coordinates, the map pans / zooms under it); a bar gives its size,
zoom range, tile count and size, the trails switch and Get; areas on the
card are outlined
- Map tools > Map areas: the downloaded areas (map/AreaStore.h,
/sdcard/maps/areas.txt) -- show (framed, outlined), rename, fill gaps,
refresh (force re-download), trails on / off, delete (in steps, keeping
tiles another area covers)
- TileDownloader: force and per-job trails options
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Waymarked Trails' transparent hiking layer, kept in /sdcard/maps-trails and
blended over the base tile at render time (Map tools > Hiking trails, NVS).
An area download fetches each tile's trails after its base tile, so
re-running an area on the card adds just the trails; with live tiles on, a
shown tile missing its trails has them fetched. Tiles without a trail are
stored as 0-byte files (no cluster on FAT).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
group() / settingRow / listRow / actionRow / choiceRow / groupNote: one card
per section, hairlines between rows, hints that wrap. Dropdowns replaced by
a centred picker list. Settings regrouped (Device, Connections, Map & data,
System); Display & power split into Display, Power and Time on L2 only
(the shared schema is unchanged), Keyboard and About get their own pages.
Radio and Repeater share one LoRa parameter block.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Shared infoCard/infoRow/infoNote helpers: muted label left, value right,
hairlines between rows, empty rows hidden. Diagnostics grouped into
sections with a received/sent packet table; GPS gets a position card and
constellation pills; About, OTA, Storage and map popups use the same
cards. Text no longer breaks after '.', clock alarm hint unclipped.
Sim-only sim_open() hook for jumping to a screen.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Power: the UI loop sleeps until something is due (never with packets
queued); screen off puts the CPU at 80 MHz, the GT911 to sleep (unless a
tap wakes the screen) and the LP5814 in standby. GPS off now cuts the
L76K's rail and UART on the L2 (L2GpsProvider). The battery divider is
powered only for a reading (measured: settles at once); readings within
2 s are reused. The SD mount is retried at most every 5 s.
Fixes: WiFi left on after leaving a scan, live tiles' WiFi kept with the
screen off on the map, an ADC read every second for the status bar, touch
polled on every pass while dark, a scan cutting an update's WiFi, relay
count not refreshing in a channel thread, raw @[nick] in room previews.
Labels skip unchanged text (no redraw).
Helpers: scrollList, dimOverlay, settingRow, flexBox, nvs::get/put,
trailFilePath (a second save in the same minute no longer overwrites),
unreadTotal. Dead code removed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Message history archived per conversation on the SD card (HIST_ARCHIVE):
restored on boot, Older/Newer paging in threads, kept count selectable
- Settings > System > Storage: card and flash usage, breakdown by maps,
messages, trails and other, kept-per-chat setting, delete history;
reads the mounted volume and warns when the FAT partition is much
smaller than the card
- Saved trails on the card: every Save is a new file, Load opens a list
with load (framed on the map), GPX export and delete
- Diagnostics: GPS data rows, last start reason, last crash summary
- Messages restored before the clock is set show their date instead of 0s
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Unlocking fades the lock screen out while the screen underneath drifts
into place; the slider unlocks on letting go at the end and springs back
when let go earlier
- Channel names no longer get a "# " prefix (thread title, channel popup,
live share targets) -- "#" marks a hashtag channel; favourite contacts in
the live share list are starred instead
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Anim.h: screens emerge from the middle (background cover fades, content
drifts 6 px), Home pages slide, popups and toasts rise and fade in
- Theme.h: accent rules (fill = primary action, dim fill = selected, text =
names/counts/modes), theme layer over the default theme, radius tokens,
accent colour picker (Settings > Display & power > LOOK, NVS mc_ui)
- Splash with the Solo and upstream versions
- Status icons in equal cells, L1-style relay marks, path window with a hop
diagram, tile download popup fits the screen (WiFi only in Settings)
- Perf: uncompressed fonts, two 120-line PSRAM buffers (~48 -> ~33 ms per
transition frame); UI_PERF_TEST harness
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Screen PIN (Settings > Display & power > Security): 4-8 digits in NVS,
keypad on the lock card after every wake and on boot, 5 misses -> 30 s pause
- Live map tiles: missing tiles at the current zoom are fetched over the saved
WiFi, written to the card and drawn; WiFi drops 30 s after leaving the map;
"Live tiles" switch in Map tools
- Firmware update (Settings > System): checks the fork's latest release,
streams the -ota.bin into the spare app slot over TLS verified with the
Arduino 3.x CA bundle, checks image magic/chip id, restarts
- Release workflow publishes *_solo_lvgl envs (merged image + -ota.bin)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Map tools hold trail, live share and arrival alert, with their options
(schema page "Map options") behind one button; back returns to the map
- Nearby gets an advert button: send now (nearby / everyone) + auto-advert
- Home page 3: Repeater, Admin (list of repeaters and room servers),
Diagnostics
- Settings: display, sound, radio (Bluetooth, WiFi), system, keyboard,
contacts & messages; units moved to Display & power
- Status bar: Bluetooth, GPS, alarm, mute, then auto-advert, trail, live
share, repeater, arrival alert in the accent colour
- Fonts: key and route glyphs
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- New env Wio_Tracker_L2_companion_solo_lvgl_v3 on pioarduino 55.03.312-1;
the 2.0.17 env stays until the new one passes the hardware checklist
- SerialBLEInterface: NimBLE variant (PIN pairing through encrypted,
authenticated characteristic properties; setAccessPermissions is a no-op)
- buzzer: i2s_std driver on IDF 5 (legacy driver kept for 2.0.17)
- ESPNOWRadio: IDF 5 callback signatures
- ui-lvgl: psramBuf() for trail drawing, tile cache, map marks, list rows,
keyboard maps and message metadata; internal heap back to 2.0.17 level
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- genericBuzzer I2S path (BUZZER_I2S): an audio task synthesises the notes
with eased edges and keeps the DMA queue fed with silence between sounds;
ES8311 setup; amp powered through the board only around sounds
- ui-core/SoundControl.h (mode, volume, built-in sounds, melody model),
SoundNotifier moved to the Core, chanctl::melody, schema Sound page
- L2: notifications, alarm / timer ring, locator sounds, Settings > Sound,
melody editor with the playing note lit, per-chat sound, mute icon
- noteIndex() on every buzzer backend; scrolling popups past screen height
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
JakubandClaude Opus 5.5