Duplicates found between the L1 and L2 frontends, and inside the L2 one:
- geo::fmtLocShare / fmtLatLon / turnDeg / isAhead (GeoUtils.h): the [LOC]
text was built in five places, the turn angle and its "ahead" threshold in
both navigations, coordinates by hand in nine. Tested.
- LiveShareEngine::setEnabled: live share was switched in three places.
- L1 waypoint share uses WaypointModel::shareText; Trail's "Share my pos"
goes through UITask::quickShareMyLocation, so it now sends to a running
live-share session as the home Map page does.
- L2 Widgets.h: switchCreate (one switch size, was four), switchRow with a
state and callback (16 hand-wired copies), switchRowOpens (Bluetooth, WiFi,
GPS), primaryButton (one height for Save / Measure / New area / Update).
GPS: with it off, starting the trail, live share or track back, sharing or
marking a position, or centring the map asks first ("GPS is off") on both
L1 and L2; Cancel leaves it undone. A share or a mark waits for a fresh fix
(a switched-off module may still report its last one), which also fixes the
L1 "Share my pos" sending a stale position. SOS still turns the GPS on itself.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- set af / dutycycle / rxdelay reject nan.
- A TX power change from the app or CLI re-baselines APC.
- CMD_SET_RADIO_PARAMS stores repeat as 0/1.
- The alarm reschedules itself when the time zone changes.
- A late ACK for an earlier DM attempt marks it delivered.
- A new auto-advert interval counts from the last advert.
- Both UIs take the TX power range from radioctl, up to MAX_LORA_TX_POWER
(30 dBm on the GAT562 30S).
- The ping timeout comes from the airtime; 3-byte path hash mode pings with
4-byte trace hashes, and trace flags are right for width 4.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Settings schema gains Privacy (position in adverts, who can ask for
status / location / sensors), Adding contacts (all or by type, max
hops, replace oldest) and Advanced radio (path hash size, double ACK,
listen before talk, interference threshold, RX boost, RX delay,
airtime factor); both UIs build their rows from it
- Auto-advert carries position only when Position in adverts is on
- ui-new accordion holds 16 sections and 128 rows
- docs: settings, tools, feature matrix
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A popup over a still screen is frozen and dimmed as it opens, so the
panel's rise redraws only the panel: 6-8 frames of 19-25 ms instead of
3-4 of 45-65 ms. Picker options are one label each (time zone list
97 -> 52 ms to build). The bottom popup no longer animates a dim of 0.
Repeater updates its hint in place (130 ms rebuild gone); Auto power,
Imperial units and Relay on rebuild the screen after the knob has
moved (rebuildSoon). -D PERF_CONTROLS times every control on the
settings screens.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A group row's text column (and an info row's key) grows into what the
controls on its right leave, and LVGL lays out children before their
parent, so its labels were first measured 1 px wide; LVGL also works out a
new label's height at its old width (0) before the real one. Each height
that changed then took another pass up the screen: 4-6 passes per screen.
rowsFit(), run before a frame's layout (LV_EVENT_REFR_START) and by
layoutNow() in place of every explicit lv_obj_update_layout(), gives each
new row's growing child the width the flex will give it, worked out from
the other children's styles and text, and labelFit() measures wrapping
labels at their real width up front. The grow stays, so a control that
can't be sized ahead only falls back to the old passes.
Layout on the device: Display page 34 -> 24 ms, Bot 33 -> 18, Quick
37 -> 22, Radio 26 -> 18, Diagnostics 20 -> 12. Sim screenshots of 26
screens unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The list fill becomes a small job queue (fill/then/fillStart, fillTick with a
25 ms budget per pass). Settings pages build section by section in
schemaRows, with the trailing extras (melodies, prune, quick messages) queued
after them so the order stays; Radio and Repeater build by group, Admin's
repeater pick like the contact list, Diag's Live tab by section. Rebuilds
that restore the scroll flush the queue first. Screens went from 220-360 ms
to 80-175 ms (build + first frame).
Diag's crash line read the core dump in flash every second (~44 ms each);
it is read once now. The perf run times every page and dismisses the USB
popup, which had covered all earlier measurements.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Every toggle / stepper wrote the prefs file straight away (0.1-0.6 s on the
ESP32's SPIFFS), which stuttered the UI and wore the flash. prefsSave() now
only marks them dirty; they're written once when the screen is left, when the
display goes off, or after 60 s at the latest -- the L1's approach. Shutdown
and the pre-restart OTA save still write immediately.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
LVGL 9.2.2 measures a SIZE_CONTENT box from its children as scrolled, so an
elastic pull past the end of a capped popup list shrank it by the overshoot,
again on every pull. lvgl_patches.py fixes calc_content_height in the
downloaded library (a build middleware for PlatformIO, called directly by the
sim's build_wasm.sh).
The five popups that each built the same panel now share popupOpen() (fit to
content / full height / under the status bar).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
group() / settingRow / listRow / actionRow / choiceRow / groupNote: one card
per section, hairlines between rows, hints that wrap. Dropdowns replaced by
a centred picker list. Settings regrouped (Device, Connections, Map & data,
System); Display & power split into Display, Power and Time on L2 only
(the shared schema is unchanged), Keyboard and About get their own pages.
Radio and Repeater share one LoRa parameter block.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Power: the UI loop sleeps until something is due (never with packets
queued); screen off puts the CPU at 80 MHz, the GT911 to sleep (unless a
tap wakes the screen) and the LP5814 in standby. GPS off now cuts the
L76K's rail and UART on the L2 (L2GpsProvider). The battery divider is
powered only for a reading (measured: settles at once); readings within
2 s are reused. The SD mount is retried at most every 5 s.
Fixes: WiFi left on after leaving a scan, live tiles' WiFi kept with the
screen off on the map, an ADC read every second for the status bar, touch
polled on every pass while dark, a scan cutting an update's WiFi, relay
count not refreshing in a channel thread, raw @[nick] in room previews.
Labels skip unchanged text (no redraw).
Helpers: scrollList, dimOverlay, settingRow, flexBox, nvs::get/put,
trailFilePath (a second save in the same minute no longer overwrites),
unreadTotal. Dead code removed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Anim.h: screens emerge from the middle (background cover fades, content
drifts 6 px), Home pages slide, popups and toasts rise and fade in
- Theme.h: accent rules (fill = primary action, dim fill = selected, text =
names/counts/modes), theme layer over the default theme, radius tokens,
accent colour picker (Settings > Display & power > LOOK, NVS mc_ui)
- Splash with the Solo and upstream versions
- Status icons in equal cells, L1-style relay marks, path window with a hop
diagram, tile download popup fits the screen (WiFi only in Settings)
- Perf: uncompressed fonts, two 120-line PSRAM buffers (~48 -> ~33 ms per
transition frame); UI_PERF_TEST harness
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- New env Wio_Tracker_L2_companion_solo_lvgl_v3 on pioarduino 55.03.312-1;
the 2.0.17 env stays until the new one passes the hardware checklist
- SerialBLEInterface: NimBLE variant (PIN pairing through encrypted,
authenticated characteristic properties; setAccessPermissions is a no-op)
- buzzer: i2s_std driver on IDF 5 (legacy driver kept for 2.0.17)
- ESPNOWRadio: IDF 5 callback signatures
- ui-lvgl: psramBuf() for trail drawing, tile cache, map marks, list rows,
keyboard maps and message metadata; internal heap back to 2.0.17 level
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- genericBuzzer I2S path (BUZZER_I2S): an audio task synthesises the notes
with eased edges and keeps the DMA queue fed with silence between sounds;
ES8311 setup; amp powered through the board only around sounds
- ui-core/SoundControl.h (mode, volume, built-in sounds, melody model),
SoundNotifier moved to the Core, chanctl::melody, schema Sound page
- L2: notifications, alarm / timer ring, locator sounds, Settings > Sound,
melody editor with the playing note lit, per-chat sound, mute icon
- noteIndex() on every buzzer backend; scrolling popups past screen height
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
JakubandClaude Opus 5.5