- Auto-Reply Bot gains Actions (!buzz/!gps/!advert) behind a new per-target
toggle nested under Commands (bot_actions_dm/ch/room); off by default.
- Bot Trigger fields accept comma-separated multiple phrases, matching any
one fires the reply.
- New user-assignable GPIO feature (Wio Tracker L1): !gpio1..!gpio4 bot
commands plus a Tools > GPIO screen. Each pin cycles Off/Input/Output;
GPIO1/GPIO2 (P0.02/P0.29, the nRF52840's AIN0/AIN5) also offer a read-only
Analog mode via direct SAADC access. GPIO3/GPIO4 (P0.09/P0.10) are the
chip's NFC1/NFC2 pins, repurposed as plain GPIO via a one-time UICR
NFCPINS bit-clear in initVariant() (adapted from Adafruit's own
nfc_to_gpio example) -- confirmed working on real hardware.
- Fix: DM/room reply-prefix ("@[nick] ") stripping happened at the wrong
layer, hiding the "To:" header on DM replies and leaking the raw prefix
into room messages' list view; a related mismatch had the history
scrollbar's sizing pass wrap room messages with the sender name still
attached, disagreeing with the actual rendered text.
Build-verified: WioTrackerL1_companion_solo_dual and
WioTrackerL1Eink_companion_solo_dual both compile and link clean
(sizeof(NodePrefs) confirmed 2720 via real build, not guessed).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
- GxEPDDisplay now uses the same single misc-fixed 6x9 font as the OLED
driver (Lemon retired there too), with baseline math updated for the
new ascent.
- Clock Tools' Alarm screen: Repeat and Armed now respond to LEFT/RIGHT
like every other multi-value/toggle field in Settings, not Enter-only;
Hour/Minute merged into one Time row edited with a hand-rolled HH:MM
digit cursor (like the Timer's), replacing the two-row DigitEditor
popups; Repeat's "Off" label now matches the codebase-wide ON/OFF
casing.
- Top status bar: battery icon now shares the same box height as the
other status icons (Bluetooth/mute/etc.) instead of standing 2px
taller, and its charge nub is properly vertically centred instead of
drifting off-centre at non-multiple-of-4 box heights.
- Small settings-gear icon glyph tweak; wio-tracker-l1 screenshot build
variant now enables DUAL_SERIAL.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The per-read VBAT_ENABLE gating from 4d46abb2 (energy optimizations)
powered the battery voltage divider HIGH for only 10ms before each ADC
read, then LOW. 10ms is too short for the high-impedance divider node
to settle before the nRF52 SAADC samples it, so readings came out high
and inconsistent (e.g. 4.6-5.0V on a LiPo that maxes ~4.2V).
Hold VBAT_ENABLE HIGH continuously again (as before 4d46abb2) so the
node is always settled at sample time, and drop the toggle + delay(10)
from getBattMilliVolts(). Standby cost is ~2uA on the 2x1M divider,
negligible next to the device's mA-level draw.
The CPU-sleep and LED-off energy optimizations from 4d46abb2 are left
untouched — those are the real savings; only the VBAT gating is reverted.
Squash merge of feat/location-beacon-alerts-autopause (v1.21).
Features:
- Live Location Sharing — broadcast position as movement-gated [LOC]
messages to a channel or contact; live shares show as map pins with
distance/bearing in Nearby Nodes and a status-bar indicator. [LOC] is
parsed in DMs, channel messages and room messages; DM shares name the
sender.
- Locator (geofence) — arm a geofence around a saved waypoint or a person
(live [LOC] or last-known position), alert on arrive/leave or near/far,
with an optional homing beeper (gated to arrive/both modes). Arm from
Tools > Locator, Nearby Nodes, or Waypoints; target picker lists
favourites first, clearable via a "None" entry. Active target is drawn
as a flag on the map.
- One active target shared across Locator / Navigate / Map via a single
resolver (resolvePersonPos / activeTargetPos) that prefers a live
[LOC] share over the last-advertised GPS fix.
- Follow live contacts — Navigate to a live-sharing contact follows them
as they move and adds an ETA line; quick-share your own position from
the Map.
- Map & status-bar upgrades — home mini-map gets a north marker, scale
tick, and a connected trail line (was disconnected dots); status line
shows tracked-node count, an arrow + distance to the active Locator/Nav
target (falling back to the nearest live-tracked contact); GPS fix icon
in the top status bar, shown only on GPS boards with GPS enabled.
- Trail auto-pause — recording freezes on stops (banking elapsed time,
breaking the map line across the idle gap) and resumes on movement
without ending the session.
- Streaming trail simplification — GPS points are simplified in-stream
via a fixed-corridor (Reumann-Witkam) pass tuned for fidelity: straight
runs collapse to their endpoints, curves stay bounded to the Min-dist
tolerance, so the 512-point buffer covers a far longer route than a
flat point budget would suggest.
- Collapsible Tools (Location / Comms / System sections, fold-in-place
like Settings) and page-indicator icons on the home carousel.
- Waypoint coordinate editor — add a waypoint by scroll-editing lat/lon
digit by digit.
Fixes:
- Critical: low-heap hang and contact loss on RAM-tight builds. Halved
message-history scrollback rings (recovering ~14 KB free heap) and
made contacts/channels/prefs persistence atomic (temp file + rename),
so an interrupted save can no longer corrupt or wipe the store.
- Serial.write() bounded so a stalled USB host can't hang the device.
- Nearby Nodes: live [LOC] senders respect the type filter, sort by
shared position, and the list refreshes so live shares bubble up.
- Map: live contacts are labelled before waypoints.
- GPS status icon hidden when GPS is off in Settings.
- Splash screen no longer truncates a pre-release tag's own dash (e.g.
v1.21-rc1) when stripping the build's commit-hash suffix.
- Null-guarded the Locator target picker; clamped loc-share channel
index on load.
Under the hood:
- -Os size optimisation on the e-ink and GAT562 30S solo envs.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
- Add build-solo-firmwares.yml: auto-detects all _solo_dual envs from platformio.ini, builds in parallel, publishes uf2 files to draft release
- Remove build-wio-tracker-l1-firmwares.yml (replaced by solo workflow)
- Add WioTrackerL1_companion_solo_dual and WioTrackerL1Eink_companion_solo_dual envs
- Wire build-solo-firmwares command in build.sh using _solo_dual suffix
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
The splash shows the upstream base version from the hardcoded MESHCORE_VERSION
build flag (distinct from FIRMWARE_VERSION, which is our solo version). The
upstream merge bumped FIRMWARE_VERSION to v1.16-solo.0 but left this flag at
1.15. Update all three occurrences (wio + eink) to 1.16.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
- Add lib/GxEPD2-patch/src/GxEPD2_BW.h: local patched copy of GxEPD2_BW.h
that exposes getBuffer()/getBufferSize() under ENABLE_SCREENSHOT guard.
Include guard (_GxEPD2_BW_H_) prevents double-inclusion of the installed
library version.
- GxEPDDisplay.h: use patched header via relative include when
ENABLE_SCREENSHOT so the patch takes precedence over the installed lib
(PlatformIO adds library paths before -I build_flags).
- DisplayDriver.h: add virtual getBuffer()/getBufferSize()/getDisplayType()
defaults (nullptr/0/0) under ENABLE_SCREENSHOT.
- SH1106Display.h / SSD1306Display.h / GxEPDDisplay.h: add concrete overrides;
getDisplayType() returns 0 (OLED) or 1 (e-ink).
- MyMesh.cpp/h: replace fragile C-cast with virtual dispatch in
handleScreenshotRequest(); extend 5-byte header to 6 bytes by appending
display_type so the host tool can decode the correct pixel layout.
- tools/screenshot.py: parse 6-byte header; add eink_buffer_to_image()
that decodes the row-major MSB-first GxEPD2 buffer with DISPLAY_ROTATION=1
(phys_x = 127-ly, phys_y = lx); dispatch on display_type.
- variants/wio-tracker-l1-eink/platformio.ini: add
[env:WioTrackerL1Eink_companion_dual_dev] with ENABLE_SCREENSHOT.
- variants/wio-tracker-l1/platformio.ini: unchanged (OLED env already exists).
Builds verified: WioTrackerL1Eink_companion_dual_dev SUCCESS,
WioTrackerL1Eink_companion_radio_ble SUCCESS (unaffected).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add MESHCORE_VERSION build flag ("1.15") to companion base configs.
Splash screen now shows MESHCORE_VERSION in the large text and the
plus firmware version (stripped of commit hash) in the Plus bar,
e.g. "1.15" large + "Plus v1.11 for Wio" below.
Change CI tag pattern to v* and simplify version extraction so tag
v1.11 maps directly to FIRMWARE_VERSION=v1.11.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Rename WioTrackerL1_companion_radio_dual_settings → WioTrackerL1_companion_dual
and WioTrackerL1Eink_companion_radio_dual → WioTrackerL1Eink_companion_dual.
Fix CI workflow: remove hardcoded branch refs so both build jobs check out
the tagged commit; add version extraction to each build job (previously
GIT_TAG_VERSION was only set in the release job, leaving FIRMWARE_VERSION
empty during builds); update build commands to use new env names.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- DualSerialInterface: guard writeFrame/isWriteBusy/isBLEConnected with
_ble_enabled to avoid BLE-after-disable race
- NearbyScreen: initialize all fields in constructor; promote D_* layout
constants to class scope; clamp _dscroll on result count change;
replace hardcoded 2 with D_VISIBLE in scroll logic; allow re-scan
from detail view via KEY_CONTEXT_MENU/KEY_ENTER
- variant.cpp: fix inconsistent indentation in initVariant()
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- DualSerialInterface: enable()/disable() control BLE only, USB always on;
USB state machine not read while BLE connected to avoid partial-frame
corruption; reset USB on BLE disconnect for clean reconnect
- Fix -UBLE_DEBUG_LOGGING (no space) to avoid PlatformIO SCons parse error
- build.sh: drop separate USB/BLE builds, dual_settings only
- wio-tracker-l1-eink: enable DUAL_SERIAL in companion_radio_ble build
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
BLE takes priority when connected; USB is always ready as fallback.
Both state machines run continuously — no BLE disconnect on USB connect.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Moved UI_HAS_JOYSTICK_UPDOWN=1 from _settings-only variants to the
WioTrackerL1CompanionBLE and WioTrackerL1CompanionUSB base configs.
The hardware always had the up/down buttons; the flag was only in
_settings as a temporary testing boundary.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
UI_SENSORS_PAGE=1 activates the existing sensor display screen in
HomeScreen — shows temperature, pressure, humidity, voltage and other
LPP-formatted sensor data from connected I2C sensors (BME280, etc.).
BME280 support is already included via sensor_base build flags.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add FIRMWARE_PLUS_BUILD compile flag to both companion sections in
platformio.ini. When set, SplashScreen shows "+ unofficial build" in
yellow below the build date. Avoids runtime string parsing — the
existing version stripping logic (cuts at first dash) is unchanged.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
build.sh sets FIRMWARE_VERSION via PLATFORMIO_BUILD_FLAGS — hardcoding
it in platformio.ini caused a macro redefinition conflict. Instead,
build_wio_tracker_l1_firmwares() now appends "-Plus" to the env var
before calling build_firmware(), so the final version string becomes
e.g. v1.15.0-Plus-abcdef.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Override the upstream FIRMWARE_VERSION define via build_flags so all
companion radio builds (USB and BLE) show "v1.15.0-Plus" on the splash
screen. The #ifndef guard in MyMesh.h makes this override automatic.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- CPU sleep: board.sleep(0) in main loop puts NRF52 into WFE/sd_app_evt_wait
between iterations; wakes on any interrupt (radio, BLE, timer). Largest
power saving of the three changes.
- VBAT_ENABLE gating: voltage divider now powered only during ADC read
(HIGH for 10ms, then LOW). Previously stayed HIGH continuously.
Fixed in both variant.cpp (init) and WioTrackerL1Board::getBattMilliVolts().
- LED off with display: PIN_LED is cleared when auto-off triggers and
restored (handed back to userLedHandler) when display wakes. Avoids
idle LED current draw during screen-off periods.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Sensors connected via the Grove I2C connector (D18/D17) were not detected
because the firmware scanned the OLED I2C bus (Wire, D14/D15) by default.
Adding ENV_PIN_SDA/SCL flags directs EnvironmentSensorManager to use Wire1,
matching the physical Grove connector pinout.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
As all NRF52 boards now have OTA support, let's remove the subclass
and integrate it into the base class.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
The startOTAUpdate() is the same for all NRF52 boards. Use a common
implementation for all boards that currently have a specific
implementation.
The following boards currently have an empty startOTAUpdate() for
whatever reasons and therefore are not inheriting NRF52BoardOTA to
keep the same state: Nano G2 Ultra, Seeed SenseCAP T1000-E,
Wio WM1110.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
Some NRF52 boards are able to use the internal power-efficient DC/DC
regulator. Add a new class that can be inherited by board classes to
enable this feature and reduce the power consumption.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
Use a common begin() method that can be called from derived classes
to contain the shared initialization code.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
* MomentaryButton: new constructor 'multiclick' param
* WIoTrackerL1: now just use joystick, joystick press for KEY_ENTER, no multi-click for snappier UI
