New M5Stack Cardputer ADV variant (ESP32-S3, ST7789 TFT, built-in TCA8418
QWERTY keyboard, PI4IOE5V6408 LoRa-cap IO-expander autodetect), and a
KeyShield accessory variant for the existing LilyGO T-Echo Lite (external
TCA8418 T9 keypad + AW21009 backlight driver). Both keyboards share one
ENV_USE_TCA8418 polling block in UITask.cpp::loop(), coexisting with the
unrelated CardKB support (different chip/address/flag).
Fixes carried in from the contributed T-Echo Lite code: swapped GPS RX/TX
pins, TX-LED hooks, TCXO voltage, missing GxEPD2_122_T61 panel include.
Fixed during integration: I2C bus was probed for an RTC before Wire.begin()
configured its pins on Cardputer ADV (silent RTC autodetect failure).
Added dedicated *_solo_dual release envs for both boards (auto-picked up by
the solo-firmware release workflow). Gave the T-Echo Lite KeyShield solo
build -Os/-Ofast-unflag like every other nRF52 solo build (was missing,
cut flash usage from 90.7% to 61.4%).
Ported the shared misc-fixed 6x9 font (full Latin/Greek/Cyrillic, opt-in via
OLED_MISC_FIXED_FONT) to ST7789Display for the Cardputer's on-screen
keyboard. ST7789Spi isn't Adafruit_GFX-based like the other single-font
drivers, and this panel's logical->physical scale is non-integer, so glyphs
are re-packed to XBM and blitted through the existing drawXbm(), which
already does correct fractional-scale boundary math, rather than
duplicating that logic.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Battery (TechoBoard.h/cpp): Added PIN_VBAT_MEAS_EN (P0.31) — the T-Echo
Lite has a gated voltage divider that must be enabled before reading. Also
added pinMode(PIN_VBAT_READ, INPUT) before each ADC read to reclaim P0.02
from other peripherals. Pin definitions hardcoded from LilyGo's
t_echo_lite_config.h.
I2C (variant.h): Corrected SDA/SCL from P0.04/P0.02 to P1.04/P1.02 per
LilyGo's IIC_1_SDA/IIC_1_SCL. The old P0.02 mapping conflicted with the
battery ADC pin.
GPS (variant.h): Corrected all five GPS pin assignments to match LilyGo's
config — UART TX/RX, wake, PPS, and power enable were all scrambled.
SPI (variant.h): Fixed SPI_INTERFACES_COUNT from _PINNUM(0, 2) to (2).
Tested on T-Echo Lite Non-Shell (USB-C, no display). Battery readings match
Heltec V4 reference within 10mV.
As all NRF52 boards now have OTA support, let's remove the subclass
and integrate it into the base class.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
The schematic shows the LC circuit for the internal DC/DC regulator
to be available. Enable it to save power.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
The startOTAUpdate() is the same for all NRF52 boards. Use a common
implementation for all boards that currently have a specific
implementation.
The following boards currently have an empty startOTAUpdate() for
whatever reasons and therefore are not inheriting NRF52BoardOTA to
keep the same state: Nano G2 Ultra, Seeed SenseCAP T1000-E,
Wio WM1110.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
Use a common begin() method that can be called from derived classes
to contain the shared initialization code.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
JakubandClaude Opus 5
pelgraine
Frieder Schrempf
Kevin Le
Jan Ryklikas