Drive WB_IO2 (slot power switch) HIGH via early constructor before the
Arduino framework initializes. Without this, the board brownouts on
POE-only power because the slot MOSFET isn't enabled early enough for
the RAK13800 POE module to deliver power to the baseboard.
Also remove the W5100S hardware reset pulse from Ethernet init — the
chip comes out of power-on reset cleanly, and toggling reset kills
the PHY link which breaks POE power delivery.
Allow for platformio.ini files to override the default values for the
following INA3221 related macros:
TELEM_INA3221_ADDRESS
TELEM_INA3221_SHUNT_VALUE
TELEM_INA3221_NUM_CHANNELS
Signed-off-by: Paul Moore <paul@paul-moore.com>
Resolve conflicts: keep both Ethernet CLI and SenseCAP power-off
button code in repeater, keep both Ethernet docs and power management
CLI docs.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
The Ethernet retry loop in repeater and room server checked
hardwareStatus() and linkStatus() before calling Ethernet.begin(),
which always returned EthernetNoHardware since hardware detection
only happens during begin(). Extract shared Ethernet CLI code into
EthernetCLI.h to prevent future divergence. Also fix time_t type
mismatch in companion radio Ethernet init.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Rename eth command to eth.status for consistency with other commands
- Rename generateDeviceMac to generateEthernetMac for clarity
- Refactor ethernet_handle_command to return false by default
- Allow new TCP clients to replace existing connections (repeater, room server, SerialEthernetInterface)
- Boot companion radio without Ethernet on init failure (LoRa-only recovery mode)
- Remove > prompt from ethernet CLI for consistency with serial interface
- Fix variable redeclaration compile error in SerialEthernetInterface when ETHERNET_STATIC_IP is defined
- Fix TCP socket leak when duplicate client detection fires
- Remove dead recv_queue and adv_restart_time members from SerialEthernetInterface
- Fix port numbers in docs (port 23 for repeater/room server CLI, port 5000 for companion radio)
- Clarify eth.status command is only available in repeater and room server firmware
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- Add #pragma once to SerialEthernetInterface.h
- Rename TCP_PORT to ETH_TCP_PORT with #ifndef guard
- Fix typos: "initalizing" → "initializing"
- Fix #elif without condition → #else for STM32 block
- Replace infinite loop on ETH init failure with halt()
- Remove heartbeat Serial.print(".") output
- Remove dead beginETH() call (ETH_ENABLED, not RAK_ETH_ENABLE)
- Comment out MESH_DEBUG and ETH_DEBUG_LOGGING build flags
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Add W5100S Ethernet adapter support for RAK4631-based firmware, enabling
TCP CLI access on port 23 as an alternative to BLE/Serial connections.
- New SerialEthernetInterface for nRF52 with DHCP, reconnection handling,
and shared WB_IO2 power pin management with GPS module
- Ethernet build targets for repeater, room server, and companion firmware
- Prevent GPS from toggling WB_IO2 when Ethernet module is active
- CI build check for all three ETH firmware targets
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Support for R1 Neo hardware. New variant and baseboard class.
* Known issues:
- power management is not currently supported
- power off via long button press is not implemented
Add support for Epson Seiko RX8130CE I2C Real-time clock.
Unless your GPS is being spoofed there isn't really a downside to
syncing more often with GPS.
I understand the RTC is very stable, but especially with powersaving now
clock drift is worse, we should sync more often.
Rastislav Vysoky
Wessel Nieboer
Ryan Gregg
Ryan Gregg
Quency-D
Paul Moore
Janez T
João BrázioandGitHub
Scott Powell
ripplebizandGitHub
kelsey hudson
Liam CottleandGitHub
Wessel Nieboer
overkillfpv
Wessel NieboerandWessel Nieboer