mkdocs will only consider the first H1 (if any) and subheaders under it for the table of contents
this increases the header levels of everything below "important concepts" by 1 so that the table of contents correctly resolves them
Post-review cleanups, no behaviour change:
- botScanCommands() parsed the command name and its two args with three
near-identical read-token loops; extracted a single readToken() lambda.
- Fn+Esc lock branch turned the display on twice (the unlock arm repeated
what the branch head already did); dropped the redundant call.
- setGpioMode()'s comment said "Cycle" (cycling lives in GpioScreen); now
describes what it actually does — set a specific mode + persist.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
- Bot Actions (!buzz/!gps/!advert/!gpio1-4) ran their side effect
immediately during botScanCommands(), before quiet-hours/cooldown/
per-contact throttle were checked -- those gates only suppressed the
reply text, not the actual buzz/GPS toggle/advert/pin write. botCommandReply()
now only records what was requested; applyPendingBotActions() runs the
deferred effects once a wrapper's throttle checks pass and the ack sent,
mirroring the existing _locfix_requested pattern. resetPendingBotActions()
clears everything on every throttled/aborted path.
- CardKB's Fn+<letter> accent-popup shortcut bypassed the locked-input gate
(it called into KeyboardWidget directly instead of through the
enqueueKey()/dequeue path every other key uses, so it wasn't discarded
while _locked). Now checks _locked itself.
- Since a locked device now correctly ignores CardKB entirely, Fn+Esc
(single press) is added as CardKB's own lock/unlock gesture -- otherwise
a CardKB-only setup had no way to unlock. Esc rather than the adjacent
Fn+Backspace, to avoid an accidental press.
- botScanCommands() now parses up to two arguments per command instead of
one. Used by "!gps fix [seconds]" to override the default 90s timeout
(clamped 15-300s) for a poor sky view where 90s isn't always enough to
reach isLocFixReady()'s HDOP/satellite bar.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Satellite count alone is a poor proxy for fix quality -- few satellites
in good geometry can beat many in poor geometry. LocationProvider now
exposes getHDOP() (default -1 = unsupported); MicroNMEA implements it.
isLocFixReady() prefers HDOP <= 2.0 when available, falling back to the
old >=8 satellite threshold for providers that don't report it (e.g.
RAK12500/u-blox).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Same fix as hotfix/admin-login-timeout (96b44460). AdminScreen's only
guard was "_phase == LOGIN" (true for any node sat at the login
screen), not that the reply actually named _target. Now also checks
pub_key against _target.id.pub_key.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
AdminScreen::onRoomLoginResult()'s only guard was "_phase == LOGIN" --
true for *any* node currently sat at the login screen, not specifically
_target. Combined with UITask::onRoomLoginResult()'s current-screen
dispatch (not requester-based), a slow reply for an earlier login
attempt (this screen's own previous target, or even MessagesScreen's)
arriving while the user has since opened Admin on a different,
password-less node -- still parked at the blank LOGIN keyboard, so
_phase == LOGIN here too -- was accepted as that new node's own login
result, flipping _admin_ok/_phase to COMMAND without ever actually
authenticating with it.
Root-caused by cancelUiPendingLogin() (previous commit): that fix
covers the "gave up, then it resolved late" path, but not "a reply for
a genuinely different pubkey arrives while merely _phase == LOGIN".
Checking pub_key against _target.id.pub_key closes that regardless of
which path let the reply through.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Same fix as hotfix/admin-login-timeout (5a5ebe9f). UITask::onRoomLoginResult()
dispatches by whichever screen is currently shown, not by who sent the
request, so a reply arriving after AdminScreen gave up (Cancel or the
timeout fix) could land on MessagesScreen instead and persist its own
unrelated _login_pw as the "confirmed" password for that pubkey.
MyMesh::cancelUiPendingLogin(pub_key) stops tracking the request on
give-up so a late reply matches nothing instead.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
UITask::onRoomLoginResult() dispatches a login reply to whichever
screen is *currently* shown (curr == admin_screen ? AdminScreen :
MessagesScreen), not to whoever actually sent the request. Neither
giving up path (manual Cancel, or the timeout added in 23f43cac) told
MyMesh to stop tracking the request, so a reply that still arrived
after the user had navigated away landed on whatever screen they'd
moved to instead -- most likely MessagesScreen, which then persisted
its own unrelated _login_pw as the "confirmed" password for that
pubkey, silently corrupting the saved password even on a genuine
success.
Adds MyMesh::cancelUiPendingLogin(pub_key), pubkey-guarded so it's a
no-op if a newer request has since overwritten ui_pending_login, called
from both of AdminScreen's give-up paths. A late reply now simply
matches nothing and is dropped.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Same fix as hotfix/admin-login-timeout (05609019). Tools > Admin >
System > "Admin password" changes the remote's admin credential but
never updated this device's saved copy, so the next login retried the
password just replaced -- likely the actual trigger behind the
"stuck on Logging in..." report. Parses CommonCLI's "password now: <v>"
success echo and saves that as the new on-device password.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Tools > Admin > System > "Admin password" (set-only, sends "password
<new>") changes the remote node's own admin credential, but nothing
updated this device's saved copy of it -- so the very next login
attempt to that node retried the password just replaced, landing
straight in the "stuck on Logging in..." case fixed in the previous
commit. Likely the actual trigger behind that report.
CommonCLI::handleCommand() always echoes a successful password change
back as "password now: <value>" (truncation and all), so parsing that
reply gives the exact value now required to log back in, rather than
trusting what we sent (which the remote may have truncated further).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Turns GPS on (if it wasn't already), waits for a stabilised fix
(isValid() + >=8 satellites, then averages 10s of readings), sends the
position, and restores GPS to whatever state it was in before -- up to
a 90s timeout, after which it reports a partial fix (if it got any
samples) or plain failure.
Replies in two parts since a fix takes seconds-to-minutes, unlike every
other bot command here: an immediate "acquiring fix..." ack (through
the existing synchronous command path), then the actual position as a
separate follow-up message once ready, delivered to whichever
destination (DM/room/channel) the request came from. Only one fix can
be in flight at a time -- a second request while one is pending gets an
immediate "already pending" instead of silently replacing it.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
AdminScreen's LOGIN phase had no timeout, unlike its COMMAND phase
(_cmd_deadline_ms). If a login reply never arrived -- most commonly a
saved password gone stale after the remote node's password changed,
silently dropped instead of nacked -- the screen stayed stuck with only
a manual Cancel to escape.
sendRoomLogin() now returns the same est_timeout sendAdminCommand()
already exposes; AdminScreen uses it to arm a deadline (poll(),
mirroring the COMMAND-phase pattern) that forgets the stale password
and returns to the picker on expiry, same as an explicit login
rejection already does.
Same fix as hotfix/admin-login-timeout (23f43cac), split out of this
branch's other in-progress work.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
AdminScreen's LOGIN phase had no timeout, unlike its COMMAND phase
(_cmd_deadline_ms). If a login reply never arrived -- most commonly a
saved password gone stale after the remote node's password changed,
silently dropped instead of nacked -- the screen stayed stuck with only
a manual Cancel to escape.
sendRoomLogin() now returns the same est_timeout sendAdminCommand()
already exposes; AdminScreen uses it to arm a deadline (poll(),
mirroring the COMMAND-phase pattern) that forgets the stale password
and returns to the picker on expiry, same as an explicit login
rejection already does.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Add Settings > Keyboard "Ext. KB" row (boards with a CardKB-capable I2C
bus only): switching it to Compact hides the letter grid and special-row
icons in favour of a one-line status (script/page, caps) plus a Fn-shortcut
reminder, since an external-keyboard typist never looks at the on-screen
grid. Accent/placeholder popups still render as before. Off by default.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Select nodes had this flag enabled, testing by the community
and hardware specs indicate this can be enabled global for all
node types using this chipset.
Any nodes down the line that may be quirky can be individually
disabled with `-U USE_CC310_HW_CRYPTO`.
CardKB is level-triggered (repeats the held byte every poll) and its Enter
key collided with the on-screen keyboard grid's own commit action, causing
duplicate characters and accidental message sends. Debounce polling and use
the CardKB v1.1 Fn modifier (confirmed working on real hardware) instead of
tracking navigation state: plain Enter now behaves like the physical centre
button, Fn+Enter submits, Fn+Tab opens the Hold-Enter equivalent, and
Fn+<letter> opens that letter's accent popup directly.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Auto-detected at boot on Wire1/Grove (addr 0x5F) -- no setting to flip, and a
no-op on boards without that bus or with nothing attached. This UI's key
codes (KEY_LEFT/UP/DOWN/RIGHT/ENTER/CANCEL) already match CardKB's own byte
protocol, so most input needs zero translation and flows through the same
key queue as physical buttons.
Two bytes get remapped in UITask::pollCardKB():
- Enter, only when the on-screen keyboard's plain grid state is active (no
placeholder/accent popup, not in cursor-mode), becomes a new KEY_KB_ENTER
sentinel meaning "submit the field" -- reusing plain KEY_ENTER there would
insert a stray character, since a CardKB typist's row/col never reflect an
intentional grid selection. Everywhere else Enter is untouched, so
selecting a placeholder or committing an accent still works normally.
- Tab (otherwise unused) becomes KEY_CONTEXT_MENU, standing in for the
"Hold-Enter" long-press gesture CardKB has no way to produce -- without it,
~30 context menus across the UI (message reply/navigate, Bot/Admin/
Repeater, ...) would be unreachable from the keyboard alone.
KeyboardWidget gains a direct-typing path: printable ASCII inserts straight
at the cursor bypassing the grid, Backspace deletes, KEY_KB_ENTER submits.
Build-verified: WioTrackerL1_companion_solo_dual and
WioTrackerL1Eink_companion_solo_dual both compile and link clean; also
smoke-tested Heltec_mesh_solar_companion_radio_ble (no ENV_PIN_SDA/SCL) to
confirm zero regression on boards without the feature.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The bot outgrew "auto-reply" once it gained Actions (!buzz/!gps/!advert/
!gpio1-4) that control device hardware remotely, not just answer messages.
Renames the Tools screen entry and all doc cross-references; already-shipped
release notes (v1.23) are left as-is to match what actually shipped under
that name.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The room server never supported RX boosted gain, while the repeater
does. Three consequences on SX1262/SX1268 boards:
- boosted gain was never applied to the radio at boot, so a room server
ran in power-saving RX mode while an identical repeater ran boosted -
a real receive-sensitivity difference with nothing pointing at it
- _prefs.rx_boosted_gain was never initialised (the prefs are memset to
0 before defaults are set), so it defaulted to off
- 'set radio.rxgain on' replied "Error: unsupported" but CommonCLI had
already written the value to prefs and saved them, so a stale setting
survived reboot and was never applied
Mirror the repeater's implementation: initialise the pref default under
the same USE_SX1262/USE_SX1268 and SX126X_RX_BOOSTED_GAIN guards, apply
it during radio init, and override setRxBoostedGain() so the CLI reports
success and takes effect.
Built Heltec_v3_room_server (SX1262) and LilyGo_T3S3_sx1276_room_server
(guards compile out cleanly).
- Auto-Reply Bot gains Actions (!buzz/!gps/!advert) behind a new per-target
toggle nested under Commands (bot_actions_dm/ch/room); off by default.
- Bot Trigger fields accept comma-separated multiple phrases, matching any
one fires the reply.
- New user-assignable GPIO feature (Wio Tracker L1): !gpio1..!gpio4 bot
commands plus a Tools > GPIO screen. Each pin cycles Off/Input/Output;
GPIO1/GPIO2 (P0.02/P0.29, the nRF52840's AIN0/AIN5) also offer a read-only
Analog mode via direct SAADC access. GPIO3/GPIO4 (P0.09/P0.10) are the
chip's NFC1/NFC2 pins, repurposed as plain GPIO via a one-time UICR
NFCPINS bit-clear in initVariant() (adapted from Adafruit's own
nfc_to_gpio example) -- confirmed working on real hardware.
- Fix: DM/room reply-prefix ("@[nick] ") stripping happened at the wrong
layer, hiding the "To:" header on DM replies and leaking the raw prefix
into room messages' list view; a related mismatch had the history
scrollbar's sizing pass wrap room messages with the sender name still
attached, disagreeing with the actual rendered text.
Build-verified: WioTrackerL1_companion_solo_dual and
WioTrackerL1Eink_companion_solo_dual both compile and link clean
(sizeof(NodePrefs) confirmed 2720 via real build, not guessed).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
ripplebizandGitHub
Liam CottleandGitHub
Talia
Jakub
taco
Nick Dunklee
agessaman
Alexander Hoffer
=UltimateCodeWarrior
fdlamotteandGitHub
NickDunkleeandGitHub