- DisplayDriver takes ColorVal; each driver's .cpp defines the UIColor roles
(window_bkg, primary_txt, ...) in its own values. ui-new draws in two:
window_bkg and primary_txt. OLED and e-ink look as before (sim screens
pixel-identical).
- E213, E290, LGFX, Null, ST7735, ST7789LCD, U8g2 taken whole from upstream
(with them the rewritten ST7735 driver and the Heltec V4 R8 TFT display).
- SH1106, SSD1306, ST7789, EinkGfxDisplay and the sim drivers converted.
- ui-orig, ui-tiny, simple_* get upstream's colour roles; the repeater's UI
taken from upstream (its power-off screen).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Fixes and features from upstream: MACThenDecrypt / command buffer
overflow fixes, ACK forwarding delay, transport code 0 as unscoped,
hidden nodes don't answer DISCOVER, LR2021/LR1121 fixes, GPS cold-start
detection and waitFor()/drain(), NMEA fix-age counters, ESP32 RTC after a
crash, remote CLI by text message (TXT_TYPE_CLI_COMMAND),
PUSH_CODE_BINARY_RESPONSE, board.loop(), new boards (Wio Tracker L1 1W,
ThinkNode M4/M8, Muzi Base, Waveshare LR1121, Pico W).
Kept ours: NodePrefs, main.cpp, every UI, GxEPDDisplay. The companion CLI
stays MyMeshCli.h's handleCliCommand(); upstream's handleCommand() calls
it. The board's FEM gains go through attachDynamicPrefs() with an adapter
over our NodePrefs fields. Upstream's JSON prefs and MultiSerialInterface
come as their own stages.
Also: the display defaults were inside RADIO_FEM_TXGAIN's #else (a
missing #endif).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
gat562_30s_mesh_kit has an always-on external PA rated at +30dBm, but the
firmware wrote tx_power_dbm straight to the SX1262 register (capped at 22),
so the app/CLI/UI never matched the real radiated power and couldn't ask
for more than 22 even though the hardware supports it.
Add a generic, macro-gated PA gain-curve resolution in
RadioLibWrapper::setTxPower() (the single choke point every TX-power path
already funnels through), reusable by any future board with a similar PA.
For this board, reuse the vendor-measured 869MHz curve from the open
upstream Meshtastic PR that added it for the same physical module
(meshtastic/firmware#11212): pick the lowest SX1262 setting whose measured
output reaches the requested dBm, clamped at the PA's saturation knee.
Bump LORA_TX_POWER/MAX_LORA_TX_POWER to 30 for this variant only -- the
other three GAT562 boards use the SX1262's own PA_BOOST (22dBm, no
external PA) and are unaffected.
Since a request below the PA's floor gain (14dBm) still radiates at that
floor, also make CommonCLICallbacks::setTxPower() return what was actually
applied, and have every setter (BLE CMD_SET_RADIO_TX_POWER, CLI "tx",
simple_repeater/room_server/sensor) persist and report that value instead
of the raw request -- so tx_power_dbm never silently disagrees with the
physical output in either direction.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The serial command buffers must stay NUL-terminated within their
bounds: if they ever aren't, strlen() can return >= sizeof(command)
and the read loop would index past the buffer. Additionally, a full
buffer now becomes a completed line (end-of-line marker placed
inside the buffer, NUL terminator kept) instead of overwriting the
terminator and silently corrupting the buffer for the next pass.
Applies to the serial CLI readers of the repeater, room server,
sensor and secure chat examples, and to the CLI rescue reader of
the companion example.
Adopts hardware Channel Activity Detection (wired into
RadioLibWrapper::isChannelActive() alongside our RSSI-threshold check
and RX duty-cycle power-save), MCU temperature telemetry, LR2021
standby workaround, DISPLAY_SCALE/FLIP overrides, NRF52Board
shutdownPeripherals() refactor, and misc upstream fixes.
Declines upstream's ConfigSerializer-based NodePrefs rewrite,
MultiSerialInterface/interface_manager, and UIColor palette system —
each would have broken large parts of the Solo-specific feature set
(NodePrefs fields, per-variant single serial_interface, enum-based
DisplayDriver::Color). Flagged as candidate follow-up migrations, not
permanent no's.
Also fixes several pre-existing bugs surfaced while chasing silent
merge breaks (stale newMsg() override signature in ui-tiny/ui-orig,
dead UIEventType::newContactMessage case, missing ContactsIterator
init), bumps FIRMWARE_VERSION/MESHCORE_VERSION to 1.17, and fixes a
missing <cstdlib> include that broke the native ConfigSerializer unit
tests.
Verified via 13+ pio run builds across ESP32/nRF52, all 3 companion UI
variants, and 7 display drivers, plus the full native unit test suite
(33/33 passing).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
* room server: added RegionMap, and new CommonCLI wiring, default_scope handling
* sensor: only minimal RegionMap wiring. Still needs work to handle default-scope
JakubandClaude Opus 5.5
Scott Powell
Wolfram Keil
João Brázio
MarekZegare4
agessaman
Quency-DandGitHub
Wessel Nieboer
liamcottle
Quency-D
Scott Powell