Add-by-coords sat in the top-level Trail action popup alongside Mark here.
Move it into the Waypoints view as a trailing "+ Add by coords" row, so the
popup stays focused on trail/marking actions and waypoint management lives
in one place. "Waypoints" is now always shown in the action menu (it hosts
the list, backtrack and the add entry), so the first waypoint can be added
by coordinates even with no trail or saved points yet.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
The on-screen keyboard has no comma or minus, so a single "lat,lon" entry
was unworkable. Replace it with a WP_ADD form: separate Lat / Lon / Label
rows plus Save. Lat/Lon take a magnitude from the keyboard and a hemisphere
(N/S, E/W) toggled with LEFT/RIGHT, so negative coordinates need no minus
key. Save validates the range, auto-names a blank label, and stores the
point via the normal waypoint path.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
New Trail action "Add by coords" creates a waypoint without a GPS fix: the
keyboard takes a "lat,lon" string (decimal degrees), parsed by the shared
geo::parseLatLon; on success it falls through to the normal label keyboard
(blank → auto WP<n>). Useful for a meeting point or a spot read off a map.
Invalid input reports "Bad coordinates".
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
While a trail exists the map now fits the recorded route (plus the live
position) and no longer folds waypoints into the bounding box, so a far-off
waypoint can't zoom the view out and squash the trail. Waypoints that
project outside the framed area are clamped to the nearest edge (marker +
label) instead of being lost off-screen. With no trail, the view still
auto-fits to the waypoints as before.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Previously a shared location was only actionable after opening the message
fullscreen; Hold Enter on a history row only ever offered Reply. Route the
DM and channel list context menus through the same buildFsMenu /
dispatchFsAction path as the fullscreen view, so Navigate / Save waypoint
appear directly on the list row when the selected message carries a
location (Navigate returns to the list on Back).
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Waypoints list → Hold Enter → Send hands the point to the Messages screen
as "[WAY]<lat>,<lon> <label>" (same text format geo::parseLatLon already
reads). The user picks a contact or channel, the text lands prefilled in
the keyboard to confirm/edit, then sends — closing the loop with the
Navigate / Save waypoint actions on the receiving end.
- QuickMsgScreen: share-compose mode (startShare/beginShareCompose). Picking
a recipient jumps straight to the prefilled keyboard; cancel returns home;
afterSend clears the mode.
- UITask::shareToMessage hands off from TrailScreen to the Messages screen.
- TrailScreen: "Send" added to the waypoint Rename/Delete popup; builds the
[WAY] payload at the {loc} precision (5 dp).
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
The shrunken ring left only a few-pixel needle in the OLED's short vertical
space. Switch to a linear heading tape: a fixed travel-direction pointer at
centre over a scrolling N..E..S..W scale (30° ticks, N/E/S/W labelled),
with the large degrees+cardinal readout below. The tape is purely linear
(no trig) and uses the available width, so it stays readable on the small
panel. Update the Compass docs to match.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Add the Settings › System "Units" (Metric/Imperial) row and update the
Trail action-menu entry from the old four-way km/h·mph·min/km·min/mi
"Units" cycle to a Speed/Pace "Readout" toggle within the global system.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Clarify in both the Map view row and the Waypoints section that the
current GPS position and all waypoints are drawn continuously, so the Map
view is useful standalone without an active trail recording.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
One character was too ambiguous to tell adjacent waypoints apart on the
map. Draw the first two characters of the label (falling back to one when
the label is a single char) in both the normal and degenerate map paths,
and widen the right-edge fit guard to the rendered text width.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
- Trail action-menu table gains Mark here / Waypoints / Clear waypoints.
- New Waypoints section: dropping (Mark here + label), independence from
the trail (/waypoints, survives reboot/Reset), map marker, the always-
present Trail-start row, the two-bearing nav view, and rename/delete.
- New Compass section: heads-up course-over-ground (no magnetometer),
rotating card, movement-only heading, GPS-fix gating.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Adds tools/trail_export.py: auto-detects the Wio port, waits for the
<?xml header, captures bytes until </gpx>, and writes a timestamped file
to tools/gpx/. Replaces the abandoned synthetic-FAT USB-MSC approach with
a simple host-side script.
- README: new "GPX Trail Export" section
- tools_screen.md: trail_export.py shown as the recommended download path,
cat/PuTTY kept as a manual fallback
- .gitignore: ignore tools/gpx/ output dir (mirrors tools/pngs/)
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
README:
- Fix typo "offical" → "official"
- File names in Firmware Variants table now match workflow output
(solo-<version>-oled.uf2 / solo-<version>-eink.uf2)
- Un-comment the E-ink Display section (now fully supported)
- Clock Screen: "sensor values" → "data fields" (covers Batt%, Nodes, Msgs)
- Tools Screen: mention nearby nodes and auto-advert in the highlight
- Promote Screenshot Tool to its own top-level section (was buried under
Contributing); fix `uv run tools/screenshot.py` invocation path
Docs:
- favourites_dial: document the 3rd pin-picker tier (all chat contacts
fallback) added in 0e0e5b93
- clock_screen: Altitude source clarified — onboard sensor (GPS or
barometric), not always GPS
- message_screen: blank lines around image tables that were inlined
Code:
- UITask.cpp: rename leftover plus_y/plus_label locals to solo_y/solo_label
in the splash-screen Solo banner
Workflow:
- workflow_dispatch builds previously labelled firmware with the branch
name (GITHUB_REF_NAME). Resolve BUILD_VERSION to the tag when run on a
tag push, else dev-<short-sha> so manual runs produce
solo-dev-abc1234-oled.uf2 etc.
Cleanup:
- remove stray docs/solo_features/settings_screen/set_scr_1_eink copy.png
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
