release-notes.md's v1.25 section already documents "Updated upstream
base to companion-v1.17.1", and that merge (68527e7b) is confirmed in
main's history -- but every MESHCORE_VERSION string, including
UITask.cpp's fallback default for boards that don't set it explicitly
(Heltec v3/v4, ThinkNode, Mesh Pocket, T-Echo), was still hardcoded to
the pre-bump "1.17". Bumped every occurrence to "1.17.1" to match what
actually shipped.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Solo's `_solo_dual` env for each board lived inside variants/<board>/, mixed
in with the shared upstream board configs (repeater, room server, plain
companion) that every MeshCore fork carries. Split them out into their own
top-level solo/<board>/ folder -- each still `extends` the board base defined
in its original variants/<board>/platformio.ini, just no longer interleaved
with it file-wise.
- platformio.ini: extra_configs picks up solo/*/platformio.ini alongside
variants/*/platformio.ini.
- build-solo-firmwares.yml: env-discovery grep now scans solo/ instead of
variants/ (the release matrix is unchanged -- same 8 envs, same names).
- pr-build-check.yml: solo/** added to the trigger paths.
- GAT562 30S Mesh Kit: dropped the separate solo_ble env -- solo_dual is a
strict superset (BLE still works, plus USB), and every other board only
ever had one solo build to begin with.
- GAT562 Mesh Watch13: renamed solo_ble -> solo_dual (added DUAL_SERIAL=1) to
match. No comment anywhere recorded whether this board's USB data lines
are actually broken out to a connector -- DUAL_SERIAL compiles and works
over BLE regardless, so worst case the USB half goes unused.
- Removed a dead AUTO_SHUTDOWN_MILLIVOLTS from the three solo envs that set
it (Heltec V3/V4, T-Echo Lite+KeyShield): that macro is only ever read in
the old ui-tiny UITask, never ui-new, which every solo build (these
included) uses -- it did nothing on any of them. Left alone everywhere
else it's set (non-solo companion envs elsewhere use ui-tiny/ui-orig, or
the flag is legitimately read); out of scope here.
- Added docs/solo_features/build_flags.md: every optional -D flag a solo
build understands (GPIO, CardKB/joystick, Hall-sensor cover lock, buzzer/
vibration, GPS switch, display/battery tuning), verified against the code
rather than the existing per-board comments, with what's already baked
into every solo build kept separate from what's opt-in.
- README: doc index + Building from source section link to the new page;
path references to the moved solo files updated to solo/<board>/.
All 8 solo_dual envs rebuilt clean after the move; native test suite (40
cases) unaffected.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Adopts hardware Channel Activity Detection (wired into
RadioLibWrapper::isChannelActive() alongside our RSSI-threshold check
and RX duty-cycle power-save), MCU temperature telemetry, LR2021
standby workaround, DISPLAY_SCALE/FLIP overrides, NRF52Board
shutdownPeripherals() refactor, and misc upstream fixes.
Declines upstream's ConfigSerializer-based NodePrefs rewrite,
MultiSerialInterface/interface_manager, and UIColor palette system —
each would have broken large parts of the Solo-specific feature set
(NodePrefs fields, per-variant single serial_interface, enum-based
DisplayDriver::Color). Flagged as candidate follow-up migrations, not
permanent no's.
Also fixes several pre-existing bugs surfaced while chasing silent
merge breaks (stale newMsg() override signature in ui-tiny/ui-orig,
dead UIEventType::newContactMessage case, missing ContactsIterator
init), bumps FIRMWARE_VERSION/MESHCORE_VERSION to 1.17, and fixes a
missing <cstdlib> include that broke the native ConfigSerializer unit
tests.
Verified via 13+ pio run builds across ESP32/nRF52, all 3 companion UI
variants, and 7 display drivers, plus the full native unit test suite
(33/33 passing).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
New M5Stack Cardputer ADV variant (ESP32-S3, ST7789 TFT, built-in TCA8418
QWERTY keyboard, PI4IOE5V6408 LoRa-cap IO-expander autodetect), and a
KeyShield accessory variant for the existing LilyGO T-Echo Lite (external
TCA8418 T9 keypad + AW21009 backlight driver). Both keyboards share one
ENV_USE_TCA8418 polling block in UITask.cpp::loop(), coexisting with the
unrelated CardKB support (different chip/address/flag).
Fixes carried in from the contributed T-Echo Lite code: swapped GPS RX/TX
pins, TX-LED hooks, TCXO voltage, missing GxEPD2_122_T61 panel include.
Fixed during integration: I2C bus was probed for an RTC before Wire.begin()
configured its pins on Cardputer ADV (silent RTC autodetect failure).
Added dedicated *_solo_dual release envs for both boards (auto-picked up by
the solo-firmware release workflow). Gave the T-Echo Lite KeyShield solo
build -Os/-Ofast-unflag like every other nRF52 solo build (was missing,
cut flash usage from 90.7% to 61.4%).
Ported the shared misc-fixed 6x9 font (full Latin/Greek/Cyrillic, opt-in via
OLED_MISC_FIXED_FONT) to ST7789Display for the Cardputer's on-screen
keyboard. ST7789Spi isn't Adafruit_GFX-based like the other single-font
drivers, and this panel's logical->physical scale is non-integer, so glyphs
are re-packed to XBM and blitted through the existing drawXbm(), which
already does correct fractional-scale boundary math, rather than
duplicating that logic.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Battery (TechoBoard.h/cpp): Added PIN_VBAT_MEAS_EN (P0.31) — the T-Echo
Lite has a gated voltage divider that must be enabled before reading. Also
added pinMode(PIN_VBAT_READ, INPUT) before each ADC read to reclaim P0.02
from other peripherals. Pin definitions hardcoded from LilyGo's
t_echo_lite_config.h.
I2C (variant.h): Corrected SDA/SCL from P0.04/P0.02 to P1.04/P1.02 per
LilyGo's IIC_1_SDA/IIC_1_SCL. The old P0.02 mapping conflicted with the
battery ADC pin.
GPS (variant.h): Corrected all five GPS pin assignments to match LilyGo's
config — UART TX/RX, wake, PPS, and power enable were all scrambled.
SPI (variant.h): Fixed SPI_INTERFACES_COUNT from _PINNUM(0, 2) to (2).
Tested on T-Echo Lite Non-Shell (USB-C, no display). Battery readings match
Heltec V4 reference within 10mV.
T-Echo Lite Non-Shell has no ePaper display, but the existing
companion BLE env inherits DISPLAY_CLASS=GxEPDDisplay from the base
env. This causes display.begin() to run on non-existent hardware,
corrupting BLE initialization and generating a random PIN that
cannot be displayed, making BLE connection impossible.
Add LilyGo_T-Echo-Lite_non_shell_companion_radio_ble env that:
- excludes DISPLAY_CLASS and ePaper-related build flags
- removes GxEPDDisplay.cpp and ui-new from build sources
- uses static BLE_PIN_CODE=123456 (avoids random PIN generation)
Also fix boards/t-echo.json:
- add nrfutil to upload protocols list
- add use_1200bps_touch=true and wait_for_upload_port=true
to enable reliable flashing via PlatformIO upload button
As all NRF52 boards now have OTA support, let's remove the subclass
and integrate it into the base class.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
The schematic shows the LC circuit for the internal DC/DC regulator
to be available. Enable it to save power.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
The startOTAUpdate() is the same for all NRF52 boards. Use a common
implementation for all boards that currently have a specific
implementation.
The following boards currently have an empty startOTAUpdate() for
whatever reasons and therefore are not inheriting NRF52BoardOTA to
keep the same state: Nano G2 Ultra, Seeed SenseCAP T1000-E,
Wio WM1110.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
Use a common begin() method that can be called from derived classes
to contain the shared initialization code.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
JakubandClaude Sonnet 5
MarekZegare4
taco
entr0p1
liamcottle
Florent
ripplebizandGitHub
Kevin Le
Huw DuddyandGitHub
jirogit
Rastislav Vysoky
pelgraine
OverkillFPVandGitHub
João Brázio
Wessel NieboerandWessel Nieboer
Frieder Schrempf
Jan Ryklikas