Resolve conflicts: keep both Ethernet CLI and SenseCAP power-off
button code in repeater, keep both Ethernet docs and power management
CLI docs.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
The Ethernet retry loop in repeater and room server checked
hardwareStatus() and linkStatus() before calling Ethernet.begin(),
which always returned EthernetNoHardware since hardware detection
only happens during begin(). Extract shared Ethernet CLI code into
EthernetCLI.h to prevent future divergence. Also fix time_t type
mismatch in companion radio Ethernet init.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Rename eth command to eth.status for consistency with other commands
- Rename generateDeviceMac to generateEthernetMac for clarity
- Refactor ethernet_handle_command to return false by default
- Allow new TCP clients to replace existing connections (repeater, room server, SerialEthernetInterface)
- Boot companion radio without Ethernet on init failure (LoRa-only recovery mode)
- Remove > prompt from ethernet CLI for consistency with serial interface
- Fix variable redeclaration compile error in SerialEthernetInterface when ETHERNET_STATIC_IP is defined
- Fix TCP socket leak when duplicate client detection fires
- Remove dead recv_queue and adv_restart_time members from SerialEthernetInterface
- Fix port numbers in docs (port 23 for repeater/room server CLI, port 5000 for companion radio)
- Clarify eth.status command is only available in repeater and room server firmware
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- Add #pragma once to SerialEthernetInterface.h
- Rename TCP_PORT to ETH_TCP_PORT with #ifndef guard
- Fix typos: "initalizing" → "initializing"
- Fix #elif without condition → #else for STM32 block
- Replace infinite loop on ETH init failure with halt()
- Remove heartbeat Serial.print(".") output
- Remove dead beginETH() call (ETH_ENABLED, not RAK_ETH_ENABLE)
- Comment out MESH_DEBUG and ETH_DEBUG_LOGGING build flags
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Add W5100S Ethernet adapter support for RAK4631-based firmware, enabling
TCP CLI access on port 23 as an alternative to BLE/Serial connections.
- New SerialEthernetInterface for nRF52 with DHCP, reconnection handling,
and shared WB_IO2 power pin management with GPS module
- Ethernet build targets for repeater, room server, and companion firmware
- Prevent GPS from toggling WB_IO2 when Ethernet module is active
- CI build check for all three ETH firmware targets
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Support for R1 Neo hardware. New variant and baseboard class.
* Known issues:
- power management is not currently supported
- power off via long button press is not implemented
Add support for Epson Seiko RX8130CE I2C Real-time clock.
Unless your GPS is being spoofed there isn't really a downside to
syncing more often with GPS.
I understand the RTC is very stable, but especially with powersaving now
clock drift is worse, we should sync more often.
- Change > to >= so stored value 1 means direct/0-hop only (liamcottle)
- Clamp max_hops to 63 on write since getPathHashCount() caps at 63 (robekl)
- Update comments to reflect encoding: 0=no limit, 1=direct only, N=up to N-1 hops
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Filter auto-add of new contacts by hop count (issues #1533, #1546).
Setting is configurable from the companion app via extended
CMD_SET/GET_AUTOADD_CONFIG protocol (0 = no limit, 1-63 = max hops).
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
The signed comparison in countBefore breaks for the max uint32_t value.
Even though callers now use getOutboundTotal(), the function itself
should be correct for all inputs.
On the T114, GPS_RESET (pin 38) is the same pin as PIN_3V3_EN.
MicroNMEALocationProvider::begin() sets pin 38 HIGH (powering the 3V3
rail) but stop() never set it back LOW, leaving the GPS module powered
even when disabled.
Assert reset pin in stop() to mirror begin(), and guard
_location->loop() behind gps_active check.
Fixesmeshcore-dev/MeshCore#1628
João BrázioandGitHub
Wessel Nieboer
Ryan GreggandClaude Opus 4.6
Scott Powell
ripplebizandGitHub
kelsey hudson
Ryan GreggandClaude Sonnet 4.6
Liam CottleandGitHub
Wessel Nieboer
overkillfpv
Quency-D
Wessel NieboerandWessel Nieboer
Wouter BijenandClaude Opus 4.6
Daniel Novak