- A pending DM shows a dot per send, as on the L1. The thread is read from
the SD archive, which a resend never updated: it does now, and the
thread's signature and patch state count the attempt.
- Nearby redraws when a node goes live, changes type or the units change;
the scan popup when a name or the remote SNR arrives.
- The user LED is active high: it was lit all the time and went dark
while transmitting.
- Sim hooks "dm" and "send" for testing a DM thread.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The quick panel, as a phone's: pulled down from the status bar (or a tap
on it). Bluetooth, WiFi, GPS, sound, trail and live share switch at a
tap; Advert opens the advert popup (moved here from the Nodes header);
Lock locks the screen; a brightness slider. Holding a tile opens its
settings. Lock and sun glyphs added to the fonts.
Fixes from rc1 testing on the L2:
- GPS status icon: none when GPS is off (the module kept its last fix
valid, so it stayed green); grey on, green with a fix. ensureGps()
turns GPS on before trusting that stale fix.
- Screen wake: the panel wakes dark, a frame is drawn, then the
backlight fades in -- no white flash. Off fades out first.
- Power off / flat battery: the chip wakes every 30 s to look for USB
power and starts when plugged in (it slept with no wake source before,
until the reset button). Plugged in when switched off: stays off until
re-plugged.
- Message ages in a conversation refresh every 2 s, as on ui-new; the
message popup keeps its age, repeaters heard and delivery up to date.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- BLE (ESP32): fast advertising (20-30 ms) for 30 s, then 152.5 ms, as the
nRF52 interface; the library default kept 30-60 ms forever
- Live map tiles: the WiFi drops after a minute with nothing missing
- ES8311 to standby while the I2S clocks are off, set up again before the
amp comes on
- Buzzer: no channel (DMA out of memory) waits out the samples instead of
spinning above the UI loop
- OTA: the image header check waits for its 16 bytes
- Comments: P10 is just the LED; the LCD SPI clock is 40 MHz on the wire
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Power: the UI loop sleeps until something is due (never with packets
queued); screen off puts the CPU at 80 MHz, the GT911 to sleep (unless a
tap wakes the screen) and the LP5814 in standby. GPS off now cuts the
L76K's rail and UART on the L2 (L2GpsProvider). The battery divider is
powered only for a reading (measured: settles at once); readings within
2 s are reused. The SD mount is retried at most every 5 s.
Fixes: WiFi left on after leaving a scan, live tiles' WiFi kept with the
screen off on the map, an ADC read every second for the status bar, touch
polled on every pass while dark, a scan cutting an update's WiFi, relay
count not refreshing in a channel thread, raw @[nick] in room previews.
Labels skip unchanged text (no redraw).
Helpers: scrollList, dimOverlay, settingRow, flexBox, nvs::get/put,
trailFilePath (a second save in the same minute no longer overwrites),
unreadTotal. Dead code removed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- The AW35615 USB-C controller (FUSB302-style registers, ID 0x91) only
reports VBUSOK with its measure block on; POWER resets to bandgap only,
so isExternalPowered() was always false. Board init turns it on
- Status bar shows a charge bolt on the cable, Diagnostics > Live has a
Power row, the GPS screen notes that charging disturbs GPS, and the
low-battery warning is skipped on USB as intended
- Roadmap: USB detection closed; GPS indoors still worse than the L1
even on battery, left open for later
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A failed ADS1115 read returned 0 mV, so the status bar showed 0 % (and the
low-battery shutdown could see an empty battery) until a reboot. Retry once,
then keep the last good value.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Seeed Wio Tracker L2 (ESP32-S3R8 16MB/8MB PSRAM, SX1262, NV3031B 320x240
QSPI LCD + GT911 touch + LP5814 backlight, TCA9535 expander gating every
rail, ADS1115 battery ADC, AW35615 USB-C, L76K GNSS).
Board layer ported from meshcore-dev/MeshCore PR #3381 (Hacuchino-hash),
kept at the same paths for an easy upstream merge. Differences:
- display: dropped the UIColor theme (not adopted in this fork)
- GpsTap diagnostics wrapper omitted; GNSS reads Serial1 directly
- nv3031b ODR fix dropped: LovyanGFX >= 1.2.30 (now pinned) defines
Panel_NV3031B::init_cmds itself -- the fix became a duplicate symbol
- MESH_DEBUG_PRINTLN with a non-literal format fixed (broke MESH_DEBUG builds)
- upload_speed 115200: baud is virtual on native USB; skips the switch
solo/wio-tracker-l2 adds Wio_Tracker_L2_companion_solo_bringup: ui-new
zoomed 2x, BOOT button only, no touch -- a hardware smoke test, not a
release target (deliberately not *_solo_dual, so CI doesn't publish it).
The real UI for this board will be a new LVGL frontend.
Verified on hardware: boot, display, radio, GPS, battery, BLE app link.
First boot takes tens of seconds while SPIFFS formats its 3.4 MB partition.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
JakubandClaude Opus 5.5