The companion_radio example was not restoring the GPS enabled/disabled
preference from flash after reboot. The preference was being saved
correctly when toggled via the mobile app, but on boot,
sensors.begin() -> initBasicGPS() unconditionally sets gps_active=false
and nothing subsequently restored the persisted state.
Added applyGpsPrefs() (matching the pattern in simple_repeater,
simple_sensor, and simple_room_server) and call it from main.cpp
after sensors.begin() to ensure the GPS hardware is initialized
before the saved preference is applied.
Resolve conflicts: keep both Ethernet CLI and SenseCAP power-off
button code in repeater, keep both Ethernet docs and power management
CLI docs.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
The Ethernet retry loop in repeater and room server checked
hardwareStatus() and linkStatus() before calling Ethernet.begin(),
which always returned EthernetNoHardware since hardware detection
only happens during begin(). Extract shared Ethernet CLI code into
EthernetCLI.h to prevent future divergence. Also fix time_t type
mismatch in companion radio Ethernet init.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Rename eth command to eth.status for consistency with other commands
- Rename generateDeviceMac to generateEthernetMac for clarity
- Refactor ethernet_handle_command to return false by default
- Allow new TCP clients to replace existing connections (repeater, room server, SerialEthernetInterface)
- Boot companion radio without Ethernet on init failure (LoRa-only recovery mode)
- Remove > prompt from ethernet CLI for consistency with serial interface
- Fix variable redeclaration compile error in SerialEthernetInterface when ETHERNET_STATIC_IP is defined
- Fix TCP socket leak when duplicate client detection fires
- Remove dead recv_queue and adv_restart_time members from SerialEthernetInterface
- Fix port numbers in docs (port 23 for repeater/room server CLI, port 5000 for companion radio)
- Clarify eth.status command is only available in repeater and room server firmware
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- Add #pragma once to SerialEthernetInterface.h
- Rename TCP_PORT to ETH_TCP_PORT with #ifndef guard
- Fix typos: "initalizing" → "initializing"
- Fix #elif without condition → #else for STM32 block
- Replace infinite loop on ETH init failure with halt()
- Remove heartbeat Serial.print(".") output
- Remove dead beginETH() call (ETH_ENABLED, not RAK_ETH_ENABLE)
- Comment out MESH_DEBUG and ETH_DEBUG_LOGGING build flags
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Add W5100S Ethernet adapter support for RAK4631-based firmware, enabling
TCP CLI access on port 23 as an alternative to BLE/Serial connections.
- New SerialEthernetInterface for nRF52 with DHCP, reconnection handling,
and shared WB_IO2 power pin management with GPS module
- Ethernet build targets for repeater, room server, and companion firmware
- Prevent GPS from toggling WB_IO2 when Ethernet module is active
- CI build check for all three ETH firmware targets
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Change > to >= so stored value 1 means direct/0-hop only (liamcottle)
- Clamp max_hops to 63 on write since getPathHashCount() caps at 63 (robekl)
- Update comments to reflect encoding: 0=no limit, 1=direct only, N=up to N-1 hops
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Filter auto-add of new contacts by hop count (issues #1533, #1546).
Setting is configurable from the companion app via extended
CMD_SET/GET_AUTOADD_CONFIG protocol (0 = no limit, 1-63 = max hops).
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Instead of overloading getOutboundCount() with a magic sentinel value,
add a dedicated getOutboundTotal() method to the PacketManager interface
that returns the total queue size without time filtering.
This eliminates the fragile convention that caused the regression and
makes the two operations — time-filtered count vs total count —
explicitly separate in the API.
* companion: new field in CMD_SET_OTHER_PARAMS, path_hash_mode
* companion: CMD_SEND_SELF_ADVERT, cmd_frame[1] now holds the path hash size (0 = zero hop, 1..3 = flood path hash size)
Scott Powell
Alejandro Ramirez
Quency-D
liamcottle
Rastislav Vysoky
Janez T
Orum
João BrázioandGitHub
Ryan GreggandClaude Opus 4.6
ripplebizandGitHub
Ryan GreggandClaude Sonnet 4.6
Wessel Nieboer
Wouter Bijen
Daniel Novak
Specter242
Wessel Nieboer