This is a consolidation of my changes for BME680 on RAK4631 nodes.
I will close my other PRs related to this and link back to this one.
*Background on change:*
This change replaces the Adafruit BME680 driver on RAK4631 with the
Bosch BSEC library. Other boards continue to use the existing
Adafruit path via ENV_INCLUDE_BME680.
This makes the IAQ portion of the sensor functional, and more accurate.
It also contains the math and/or CayenneLPP fixes from my other PRs.
The Bosch code also appears to handle calibrating sensor aging as well,
whereas the Adafruit code is just looking at blind values that can drift
with time. Pretty cool to see this shooting out useful data!
RAK4631 platform.io is set to override to ENV_INCLUDE_BME680_BSEC while
leaving the Adafruit code for other node types. (If this becomes applicable
for other node types in future, awesome! I just don't have hardware
to test against.)
Using the BSEC library introduces IAQ sensor calibration, and saves
the calibration state periodically so it does not have to calibrate
again later.
At startup the IAQ sensor takes 30 minutes to heat and to hit a baseline,
then starts calibrating. Once calibrated, it will save those settings
and will only write settings again if calibration falls back and restores
back to state 3.
This fix also has the gas resistance math fix that was in
[pull 2146](https://github.com/meshcore-dev/MeshCore/pull/2146) so
the adafruit path also can at least show accurate values instead
of looping negative.
Also includes the fix from [pull 2149](https://github.com/meshcore-dev/MeshCore/pull/2149) so the pressure output isn't truncated to 1hPa steps.
*Fixes/Changes:*
- Add bsec_config_iaq[] with the 3.3V/3s-LP/28d calibration profile
- BSEC init applies setConfig() for voltage-correct heater targeting
- IAQ, heat-compensated temperature/humidity, pressure, and altitude
reported over CayenneLPP
- IAQ accuracy reported as analog input over CayenneLPP (0,1,2,3)
- Calibration state persisted to /bsec_state.bin on nRF52 internal
flash; written only when iaqAccuracy improves to >= 2, should
keep write frequency well within flash endurance over device lifetime
- Fix non-BSEC query_bme680: float pressure division, addGenericSensor
for gas resistance (was addAnalogInput, overflows at > 327 Ohm)
- loop() correctly gated for both GPS and BSEC-only builds
- Add fix_bsec_lib.py extra_script to resolve nRF52840 hard-float ABI
mismatch in Bosch's PlatformIO packaging, silly Bosch
One general note outside of this code change: I noticed while BME680
_functions_ in companion nodes, since companion nodes run Bluetooth,
BLE preempts the CPU, and can do so mid-I2C-transaction.
This can cause the BME680 to see an anomaly and drop calibration and
start a recalibrate. This is behavior that will exist (and has existed)
regardless of using the Adafruit or Bosch paths.
This particular companion behavior does not seem to occur in sensor
or repeater nodes since their BLE is off. Probably affects other
I2C devices as well.
*Tests:*
- RAK19003
- RAK19007
- RAK19001
- repeater, sensor, companion
- SensorManager::getAvailableLPPTypes() reports which LPP types will be
present based on initialized sensor flags (temp, humidity, pressure, etc.)
- Sensors page renders one row per available type; shows "--" for any sensor
that hasn't produced a reading yet instead of hiding the row entirely
- LPPReader: add readLuminosity, readPercentage, readConcentration, readDistance
- All known LPP types now have proper names and units in the sensor display
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
This slipped through in PR #2327 and I noticed because the TechoBoard.h
for my variant doesn't include the Wire header, so the source file
in question does not coincidentally obtain a copy.
This is a medium-ish refactor to attempt to clean up sensor handling logic both for board stability and future potential growth before the code becomes all spaghetti and meatballs.
I'd be curious to see if anyone running sensors out there that knows how to build and flash MeshCore code could give this a try and see how it behaves. It is working fine on my end on multiple nodes.
PR notes are gigantic because it is a fundamental behavior repair for sensors, so I wanted to over-explain. Also, if it hadn't been mentioned previously, push-back is always welcome. I'm just spending my time trying to clean up / fix / enhance this corner of the firmware, and want to contribute my improvements back to the project.
**Problem:**
Current MeshCore code makes no attempt to see what sensors are actually available on the I2C bus at startup and blindly tries to interact with sensors. This has some very bad side-effects, like if a sensor that is unsupported, or has a weird initialization process, the MeshCore node will just hang at boot and never successfully start up and ostensibly looks bricked, or the INA226 and SHT4X both sharing the same address and the code just silently fighting.
The current implementation also gloms sensor readouts from the MCU and environment sensors onto the same telemetry channel, with some arbitrary exceptions for incrementing channels based on certain behavioral situations. The MCU temperature and external temperature sensors would appear on channel 1, and it wouldn't be possible to tell which sensor the temperature value was coming from.
Per [CayenneLPP](https://github.com/myDevicesIoT/CayenneLPP): *Data Channel: Uniquely identifies each sensor in the device across frames, eg. “indoor sensor”* So this channel division implementation falls inline with what CayenneLPP intended. There are up to 256 channels available. So I tried to model this change in that behavioral style.
**Proposed Improvement:**
This implementation scans the I2C bus for what devices are present, sets each sensor to its own CayenneLPP channel, and keeps MCU telemetry on channel 1 only. So Channel 1 is always "self" and no confusion can result.
Details:
- Channel 1 is always the MCU and things about it, so you always know that telemetry is from the board itself. Exception is GPS, GPS stays on channel 1 as well since it is "about the board" even though it's a bit gray-area as GPS can often be a secondary chip.
- Each sensor board is allocated to a dedicated CayenneLPP channel, so if you are reading from that channel, you know the data is from that sensor only. (Sensors emitting more than one of the same type of measurement are exceptions.)
- `scanI2CBus()` probes addresses 0x08–0x77 with raw `beginTransmission`/`endTransmission`. No sensor library is touched until after this completes. This will prevent sensor-based boot hangs, unknown or unresponsive devices never reach a library init call.
- Created `SENSOR_TABLE` a compile-time array that is gated by the existing `ENV_INCLUDE_*` macros. A sentinel `{ 0, nullptr, nullptr, nullptr }` at the end keeps the array non-empty regardless of which sensors are enabled, avoiding zero-length array warnings.
- When `begin()` is called, scan first, then loop: skip if address not detected, skip if `init()` returns 0, otherwise register one ActiveSensor entry per sub-channel.
- `querySensors()` I replaced the entire #ifdef chain with a 3-line loop.
- T1000-E has its own T1000SensorManager, so it should be completely unaffected by this change.
- SHT4X quirky initialization behavior is retained.
- MLX90614 - git commits around this didn't have any notes as to why it is reporting ambient temperature on a separate channel as well as the object temperature, as the ambient temperature is used internally to compute the object temperature and not really needed for the sensor's purpose - just the same, kept the existing behavior of reporting the ambient temperature one channel above the channel assigned to the sensor
- All `bool *_initialized` fields are gone, replaced with `ActiveSensor _active_sensors[16]` (query function pointer and sub-channel index) and `_active_sensor_count. SensorDef` lives entirely in the `.cpp` so the header has no dependency on it.
- Details on the INA226 and SHT4X: both default to address 0x44, the old code had a bug and would have both begin() calls fire and they would just fight each other silently. In the new code, the respective sensor code is only called if the device is actually present, however, if both were present simultaneously, SHT4X comes first in the table and would win, and INA226 would return false and be skipped. The INA226 has 16 possible addresses that are configurable in the hardware itself, so in a potential scenario where both sensors would be present, the person implementing that design could take that into account.
- BME680 gas resistance will now transmit on the same channel as the rest of BME680 telemetry which is inline with CayenneLPP standards. Coupling this PR with https://github.com/meshcore-dev/MeshCore/pull/2146 streamline the whole sensor telemetry, and with https://github.com/meshcore-dev/MeshCore/pull/2149 will overall improve BME680 handling. The gas resistance sensor actually has a binary library to make it more useful, calibration, accounting for age of sensor, and other improvements, but since that adds more flash consumption, I have omitted that in PRs thus far.
- RAK12035 and other current upstream dev branch changes integrated.
Allow for platformio.ini files to override the default values for the
following INA3221 related macros:
TELEM_INA3221_ADDRESS
TELEM_INA3221_SHUNT_VALUE
TELEM_INA3221_NUM_CHANNELS
Signed-off-by: Paul Moore <paul@paul-moore.com>
Unless your GPS is being spoofed there isn't really a downside to
syncing more often with GPS.
I understand the RTC is very stable, but especially with powersaving now
clock drift is worse, we should sync more often.
On the T114, GPS_RESET (pin 38) is the same pin as PIN_3V3_EN.
MicroNMEALocationProvider::begin() sets pin 38 HIGH (powering the 3V3
rail) but stop() never set it back LOW, leaving the GPS module powered
even when disabled.
Assert reset pin in stop() to mirror begin(), and guard
_location->loop() behind gps_active check.
Fixesmeshcore-dev/MeshCore#1628
If no GPS was detected, revert the hardware to the initial state,
otherwise we may see conflicts or increased power consumption on some
boards.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
Serial1 is always true. If we want to check for the presence of a GPS
receiver, we need to check if any data was received.
Signed-off-by: Frieder Schrempf <frieder@fris.de>
Make GPS update interval configurable via settings instead of using hardcoded 1 second value. The interval is persisted from preferences and can be adjusted at runtime through the sensor manager settings interface
