Settings > Radio gains a repeater toggle, 16 community-suggested radio
presets plus manual Freq/SF/BW/CR tuning (digit-by-digit Freq editor),
4 persisted user preset slots, and the packet pool bumped 16->32 so
queued retransmits stop starving incoming-packet allocation while
relaying.
Four opt-in politeness knobs (skip-advert, max-hops, yield, min-SNR),
all flood-only and off by default, plus overhear suppression that
cancels a queued retransmit if a peer relays the same packet first.
Adaptive Power Control is suppressed while relaying (pins TX power to
the ceiling) and duty-cycle RX is forced off, since a repeater needs
to hear and relay at consistent power.
A dedicated Tools > Repeater screen consolidates the toggle, the
politeness knobs, and live forwarding stats, plus an optional "Custom"
radio profile — a dedicated frequency/SF/BW/CR for relaying, separate
from the companion's own network, band-matched to the companion
frequency by default and used everywhere a radio change can happen
(boot, on-device toggle, app-driven CMD_SET_RADIO_PARAMS, Settings
radio edits) so the device never silently falls back to the wrong
params mid-relay.
Diagnostics gains the actually-forwarded packet count, real heap-free
via mallinfo(), a reset-counters popup, and hardened loop-detect
bounds. Also: a frequency-floor fix and a float-equality preset-match
fix in the repeater profile logic, deduped BW-table/valCol/profile-
seeding helpers shared between Settings and the Repeater screen, and
a build.sh fix tolerating control characters in `pio project config`'s
JSON dump.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Two independent, default-off toggles under Settings › Radio.
Pwr save: hardware RX duty-cycle (SX126x SetRxDutyCycle via
startReceiveDutyCycleAuto). The chip cycles RX↔sleep and wakes on a preamble —
no MCU state machine; recvRaw reads the packet exactly as in continuous RX.
Falls back to continuous RX on non-SX126x. (Replaces an earlier software-CAD
state machine that fought the hardware: polling a warm-sleeping chip gave a
phantom-busy channel that stalled TX ~4 s and dropped ACKs in the scan gaps.)
Auto pwr: Adaptive Power Control. tx_power_dbm becomes a ceiling; actual TX
power tracks the reverse-link SNR margin (measured above the per-SF demod floor,
EWMA-smoothed, proportional step with a deadband). Feedback comes from direct /
room-server ACKs and, for channels (no ACK), from hearing a repeater rebroadcast
our own flood; a lost confirmation ramps power back up so channel sends can't get
stranded below what the repeaters can hear.
Prefs schema 0xC0DE0009 (rx_powersave, tx_apc). Radio page / name bar show the
live TX power; noise floor reads n/a while duty-cycling.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
1. warm sleep
2. wake to stdby
3. Calibrate(0x7F) to reset all internal blocks
4. re-apply DIO2 RF / boosted gain & register patch to make sure
everything is as it was
This change counts when readData returns an err code other than RADIOLIB_ERR_NONE. In most cases this is going to be a CRC error. This counter is exposed in the `stats-packets` command, and in the repeater stats payload (4 additional bytes to the payload, which is now 56 bytes with this change. My incompetent robot claims the total payload size is 96 bytes (unverified but probably close).
This should significantly reduce power consumption in hibernation.
Fixes: #1014
Signed-off-by: Jaroslav Škarvada <jskarvad@redhat.com>
Signed-off-by: Frieder Schrempf <frieder@fris.de> # generalize for all radios and UIs
JakubandClaude Sonnet 4.6
Scott Powell
OverkillFPVandGitHub
João Brázio
Wessel NieboerandWessel Nieboer
Chris
Jaroslav ŠkarvadaandFrieder Schrempf
recrof