mirror of
https://github.com/MarekZegare4/MeshCore-Solo.git
synced 2026-09-14 15:16:40 +00:00
JakubandClaude Opus 5
05e57357d3
New M5Stack Cardputer ADV variant (ESP32-S3, ST7789 TFT, built-in TCA8418 QWERTY keyboard, PI4IOE5V6408 LoRa-cap IO-expander autodetect), and a KeyShield accessory variant for the existing LilyGO T-Echo Lite (external TCA8418 T9 keypad + AW21009 backlight driver). Both keyboards share one ENV_USE_TCA8418 polling block in UITask.cpp::loop(), coexisting with the unrelated CardKB support (different chip/address/flag). Fixes carried in from the contributed T-Echo Lite code: swapped GPS RX/TX pins, TX-LED hooks, TCXO voltage, missing GxEPD2_122_T61 panel include. Fixed during integration: I2C bus was probed for an RTC before Wire.begin() configured its pins on Cardputer ADV (silent RTC autodetect failure). Added dedicated *_solo_dual release envs for both boards (auto-picked up by the solo-firmware release workflow). Gave the T-Echo Lite KeyShield solo build -Os/-Ofast-unflag like every other nRF52 solo build (was missing, cut flash usage from 90.7% to 61.4%). Ported the shared misc-fixed 6x9 font (full Latin/Greek/Cyrillic, opt-in via OLED_MISC_FIXED_FONT) to ST7789Display for the Cardputer's on-screen keyboard. ST7789Spi isn't Adafruit_GFX-based like the other single-font drivers, and this panel's logical->physical scale is non-integer, so glyphs are re-packed to XBM and blitted through the existing drawXbm(), which already does correct fractional-scale boundary math, rather than duplicating that logic. Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
31 lines
819 B
C++
31 lines
819 B
C++
#include <Arduino.h>
|
|
#include "CardputerADVBoard.h"
|
|
|
|
uint32_t deviceOnline = 0x00;
|
|
|
|
void CardputerADVBoard::begin() {
|
|
|
|
ESP32Board::begin();
|
|
|
|
// Configure user button
|
|
pinMode(PIN_USER_BTN, INPUT);
|
|
|
|
// Configure LoRa Pins
|
|
pinMode(P_LORA_MISO, INPUT_PULLUP);
|
|
// pinMode(P_LORA_DIO_1, INPUT_PULLUP);
|
|
|
|
#ifdef P_LORA_TX_LED
|
|
digitalWrite(P_LORA_TX_LED, HIGH); // inverted pin for SX1276 - HIGH for off
|
|
#endif
|
|
|
|
esp_reset_reason_t reason = esp_reset_reason();
|
|
if (reason == ESP_RST_DEEPSLEEP) {
|
|
long wakeup_source = esp_sleep_get_ext1_wakeup_status();
|
|
if (wakeup_source & (1 << P_LORA_DIO_1)) {
|
|
startup_reason = BD_STARTUP_RX_PACKET; // received a LoRa packet (while in deep sleep)
|
|
}
|
|
|
|
rtc_gpio_hold_dis((gpio_num_t)P_LORA_NSS);
|
|
rtc_gpio_deinit((gpio_num_t)P_LORA_DIO_1);
|
|
}
|
|
} |