rak4631: set lockout voltage to 0V

Fix pow() and rand() are calculated for every forwarded packet, but we only need it for flood advert. Also fixes 'paket' typo.

Co-authored-by: Wessel <wessel@weebl.me>

docs/cli_commands.md

@@ -51,7 +51,7 @@
 - `time <epoch_seconds>`
 
 **Parameters:**
-- `epoc_seconds`: Unix epoc time
+- `epoch_seconds`: Unix epoch time
 
 ---
 
@@ -134,7 +134,7 @@
 
 ---
 
-### End capture of rx log to node sotrage
+### End capture of rx log to node storage
 **Usage:** `log stop`
 
 ---
@@ -198,7 +198,7 @@
 
 **Default:** Varies by board
 
-**Notes:** This setting only controls the power level of the LoRa chip. Some nodes have an additional power amplifier stage which increases the total output. Referr to the node's manual for the correct setting to use. **Setting a value too high may violate the laws in your country.**
+**Notes:** This setting only controls the power level of the LoRa chip. Some nodes have an additional power amplifier stage which increases the total output. Refer to the node's manual for the correct setting to use. **Setting a value too high may violate the laws in your country.**
 
 ---
 
@@ -228,6 +228,7 @@
 **Default:** `869.525`
 
 **Note:** Requires reboot to apply
+**Serial Only:** `set freq <frequency>`
 
 ### System
 
@@ -293,17 +294,16 @@
 
 #### View or change this node's admin password
 **Usage:**
-- `get password`
-- `set password <password>`
+- `password <new_password>`
 
 **Parameters:**
-- `password`: Admin password
+- `new_password`: New admin password
 
 **Set by build flag:** `ADMIN_PASSWORD`
 
 **Default:** `password`
 
-**Note:** Echoed back for confirmation
+**Note:** Command reply echoes the updated password for confirmation.
 
 **Note:** Any node using this password will be added to the admin ACL list.
 
@@ -768,7 +768,7 @@ region save
 - `gps advert <policy>`
 
 **Parameters:** 
-- `policy`: `none`|`shared`|`prefs` 
+- `policy`: `none`|`share`|`prefs` 
   - `none`: don't include location in adverts
   - `share`: share gps location (from SensorManager)
   - `prefs`: location stored in node's lat and lon settings

examples/companion_radio/MyMesh.cpp

@@ -811,7 +811,7 @@ MyMesh::MyMesh(mesh::Radio &radio, mesh::RNG &rng, mesh::RTCClock &rtc, SimpleMe
 
   // defaults
   memset(&_prefs, 0, sizeof(_prefs));
-  _prefs.airtime_factor = 1.0; // one half
+  _prefs.airtime_factor = 1.0;
   strcpy(_prefs.node_name, "NONAME");
   _prefs.freq = LORA_FREQ;
   _prefs.sf = LORA_SF;

examples/simple_repeater/MyMesh.cpp

@@ -396,6 +396,23 @@ File MyMesh::openAppend(const char *fname) {
 #endif
 }
 
+static uint8_t max_loop_minimal[] =  { 0, /* 1-byte */  4, /* 2-byte */  2, /* 3-byte */  1 };
+static uint8_t max_loop_moderate[] = { 0, /* 1-byte */  2, /* 2-byte */  1, /* 3-byte */  1 };
+static uint8_t max_loop_strict[] =   { 0, /* 1-byte */  1, /* 2-byte */  1, /* 3-byte */  1 };
+
+bool MyMesh::isLooped(const mesh::Packet* packet, const uint8_t max_counters[]) {
+  uint8_t hash_size = packet->getPathHashSize();
+  uint8_t hash_count = packet->getPathHashCount();
+  uint8_t n = 0;
+  const uint8_t* path = packet->path;
+  while (hash_count > 0) {      // count how many times this node is already in the path
+    if (self_id.isHashMatch(path, hash_size)) n++;
+    hash_count--;
+    path += hash_size;
+  }
+  return n >= max_counters[hash_size];
+}
+
 bool MyMesh::allowPacketForward(const mesh::Packet *packet) {
   if (_prefs.disable_fwd) return false;
   if (packet->isRouteFlood() && packet->getPathHashCount() >= _prefs.flood_max) return false;
@@ -403,6 +420,29 @@ bool MyMesh::allowPacketForward(const mesh::Packet *packet) {
     MESH_DEBUG_PRINTLN("allowPacketForward: unknown transport code, or wildcard not allowed for FLOOD packet");
     return false;
   }
+  if (packet->isRouteFlood() && _prefs.loop_detect != LOOP_DETECT_OFF) {
+    const uint8_t* maximums;
+    if (_prefs.loop_detect == LOOP_DETECT_MINIMAL) {
+      maximums = max_loop_minimal;
+    } else if (_prefs.loop_detect == LOOP_DETECT_MODERATE) {
+      maximums = max_loop_moderate;
+    } else {
+      maximums = max_loop_strict;
+    }
+    if (isLooped(packet, maximums)) {
+      MESH_DEBUG_PRINTLN("allowPacketForward: FLOOD packet loop detected!");
+      return false;
+    }
+  }
+  // Limit flood advert paket forwarding using a probabilistic reduction defined by P(h) = 0.308^(hops-1)
+  // https://github.com/meshcore-dev/MeshCore/issues/1223
+  if (packet->getPayloadType() == PAYLOAD_TYPE_ADVERT && packet->isRouteFlood()) {
+    double roll_dice = (double)rand() / RAND_MAX;
+    double forw_prob = pow(_prefs.flood_advert_base, packet->path_len - 1);
+    if (roll_dice > forw_prob)
+      return false;
+  }
+
   return true;
 }
 
@@ -506,7 +546,10 @@ bool MyMesh::filterRecvFloodPacket(mesh::Packet* pkt) {
   if (pkt->getRouteType() == ROUTE_TYPE_TRANSPORT_FLOOD) {
     recv_pkt_region = region_map.findMatch(pkt, REGION_DENY_FLOOD);
   } else if (pkt->getRouteType() == ROUTE_TYPE_FLOOD) {
-    if (region_map.getWildcard().flags & REGION_DENY_FLOOD) {
+      if ((pkt->getPayloadType() == PAYLOAD_TYPE_GRP_TXT ||
+           pkt->getPayloadType() == PAYLOAD_TYPE_GRP_DATA ||
+           pkt->getPayloadType() == PAYLOAD_TYPE_ADVERT) &&
+          region_map.getWildcard().flags & REGION_DENY_FLOOD) {
       recv_pkt_region = NULL;
     } else {
       recv_pkt_region =  &region_map.getWildcard();
@@ -824,7 +867,7 @@ MyMesh::MyMesh(mesh::MainBoard &board, mesh::Radio &radio, mesh::MillisecondCloc
 
   // defaults
   memset(&_prefs, 0, sizeof(_prefs));
-  _prefs.airtime_factor = 1.0;   // one half
+  _prefs.airtime_factor = 1.0;
   _prefs.rx_delay_base = 0.0f;   // turn off by default, was 10.0;
   _prefs.tx_delay_factor = 0.5f; // was 0.25f
   _prefs.direct_tx_delay_factor = 0.3f; // was 0.2
@@ -838,7 +881,8 @@ MyMesh::MyMesh(mesh::MainBoard &board, mesh::Radio &radio, mesh::MillisecondCloc
   _prefs.cr = LORA_CR;
   _prefs.tx_power_dbm = LORA_TX_POWER;
   _prefs.advert_interval = 1;        // default to 2 minutes for NEW installs
-  _prefs.flood_advert_interval = 12; // 12 hours
+  _prefs.flood_advert_interval = 0; // 12 hours
+  _prefs.flood_advert_base = 0.308f;
   _prefs.flood_max = 64;
   _prefs.interference_threshold = 0; // disabled
 

examples/simple_repeater/MyMesh.h

@@ -128,6 +128,7 @@ class MyMesh : public mesh::Mesh, public CommonCLICallbacks {
   mesh::Packet* createSelfAdvert();
 
   File openAppend(const char* fname);
+  bool isLooped(const mesh::Packet* packet, const uint8_t max_counters[]);
 
 protected:
   float getAirtimeBudgetFactor() const override {

examples/simple_room_server/MyMesh.cpp

@@ -276,7 +276,17 @@ uint32_t MyMesh::getDirectRetransmitDelay(const mesh::Packet *packet) {
 
 bool MyMesh::allowPacketForward(const mesh::Packet *packet) {
   if (_prefs.disable_fwd) return false;
-  if (packet->isRouteFlood() && packet->getPathHashCount() >= _prefs.flood_max) return false;
+  if (packet->isRouteFlood() && packet->path_len >= _prefs.flood_max) return false;
+
+  // Limit flood advert packet forwarding using a probabilistic reduction defined by P(h) = base^(hops-1)
+  // https://github.com/meshcore-dev/MeshCore/issues/1223
+  if (packet->getPayloadType() == PAYLOAD_TYPE_ADVERT && packet->isRouteFlood()) {
+    double roll_dice = (double)rand() / RAND_MAX;
+    double forw_prob = pow(_prefs.flood_advert_base, packet->path_len - 1);
+    if (roll_dice > forw_prob)
+      return false;
+  }
+
   return true;
 }
 
@@ -599,7 +609,7 @@ MyMesh::MyMesh(mesh::MainBoard &board, mesh::Radio &radio, mesh::MillisecondCloc
 
   // defaults
   memset(&_prefs, 0, sizeof(_prefs));
-  _prefs.airtime_factor = 1.0;   // one half
+  _prefs.airtime_factor = 1.0;
   _prefs.rx_delay_base = 0.0f;   // off by default, was 10.0
   _prefs.tx_delay_factor = 0.5f; // was 0.25f;
   _prefs.direct_tx_delay_factor = 0.2f; // was zero
@@ -615,6 +625,7 @@ MyMesh::MyMesh(mesh::MainBoard &board, mesh::Radio &radio, mesh::MillisecondCloc
   _prefs.disable_fwd = 1;
   _prefs.advert_interval = 1;        // default to 2 minutes for NEW installs
   _prefs.flood_advert_interval = 12; // 12 hours
+  _prefs.flood_advert_base = 0.308f;
   _prefs.flood_max = 64;
   _prefs.interference_threshold = 0; // disabled
 #ifdef ROOM_PASSWORD

examples/simple_secure_chat/main.cpp

@@ -281,7 +281,7 @@ public:
   {
     // defaults
     memset(&_prefs, 0, sizeof(_prefs));
-    _prefs.airtime_factor = 2.0;    // one third
+    _prefs.airtime_factor = 1.0;
     strcpy(_prefs.node_name, "NONAME");
     _prefs.freq = LORA_FREQ;
     _prefs.tx_power_dbm = LORA_TX_POWER;

examples/simple_sensor/SensorMesh.cpp

@@ -706,7 +706,7 @@ SensorMesh::SensorMesh(mesh::MainBoard& board, mesh::Radio& radio, mesh::Millise
 
   // defaults
   memset(&_prefs, 0, sizeof(_prefs));
-  _prefs.airtime_factor = 1.0;    // one half
+  _prefs.airtime_factor = 1.0;
   _prefs.rx_delay_base =   0.0f;  // turn off by default, was 10.0;
   _prefs.tx_delay_factor = 0.5f;   // was 0.25f
   _prefs.direct_tx_delay_factor = 0.2f; // was zero

src/Dispatcher.cpp

@@ -8,7 +8,9 @@
 
 namespace mesh {
 
-#define MAX_RX_DELAY_MILLIS   32000  // 32 seconds
+#define MAX_RX_DELAY_MILLIS        32000  // 32 seconds
+#define MIN_TX_BUDGET_RESERVE_MS   100    // min budget (ms) required before allowing next TX
+#define MIN_TX_BUDGET_AIRTIME_DIV  2      // require at least 1/N of estimated airtime as budget before TX
 
 #ifndef NOISE_FLOOR_CALIB_INTERVAL
   #define NOISE_FLOOR_CALIB_INTERVAL   2000     // 2 seconds
@@ -20,12 +22,34 @@ void Dispatcher::begin() {
   _err_flags = 0;
   radio_nonrx_start = _ms->getMillis();
 
+  duty_cycle_window_ms = getDutyCycleWindowMs();
+  float duty_cycle = 1.0f / (1.0f + getAirtimeBudgetFactor());
+  tx_budget_ms = (unsigned long)(duty_cycle_window_ms * duty_cycle);
+  last_budget_update = _ms->getMillis();
+
   _radio->begin();
   prev_isrecv_mode = _radio->isInRecvMode();
 }
 
 float Dispatcher::getAirtimeBudgetFactor() const {
-  return 2.0;   // default, 33.3%  (1/3rd)
+  return 1.0;
+}
+
+void Dispatcher::updateTxBudget() {
+  unsigned long now = _ms->getMillis();
+  unsigned long elapsed = now - last_budget_update;
+
+  float duty_cycle = 1.0f / (1.0f + getAirtimeBudgetFactor());
+  unsigned long max_budget = (unsigned long)(getDutyCycleWindowMs() * duty_cycle);
+  unsigned long refill = (unsigned long)(elapsed * duty_cycle);
+  
+  if (refill > 0) {
+    tx_budget_ms += refill;
+    if (tx_budget_ms > max_budget) {
+      tx_budget_ms = max_budget;
+    }
+    last_budget_update = now;
+  }
 }
 
 int Dispatcher::calcRxDelay(float score, uint32_t air_time) const {
@@ -61,11 +85,24 @@ void Dispatcher::loop() {
   if (outbound) {  // waiting for outbound send to be completed
     if (_radio->isSendComplete()) {
       long t = _ms->getMillis() - outbound_start;
-      total_air_time += t;  // keep track of how much air time we are using
+      total_air_time += t;
       //Serial.print("  airtime="); Serial.println(t);
 
-      // will need radio silence up to next_tx_time
-      next_tx_time = futureMillis(t * getAirtimeBudgetFactor());
+      updateTxBudget();
+
+      if (t > tx_budget_ms) {
+        tx_budget_ms = 0;
+      } else {
+        tx_budget_ms -= t;
+      }
+
+      if (tx_budget_ms < MIN_TX_BUDGET_RESERVE_MS) {
+        float duty_cycle = 1.0f / (1.0f + getAirtimeBudgetFactor());
+        unsigned long needed = MIN_TX_BUDGET_RESERVE_MS - tx_budget_ms;
+        next_tx_time = futureMillis((unsigned long)(needed / duty_cycle));
+      } else {
+        next_tx_time = _ms->getMillis();
+      }
 
       _radio->onSendFinished();
       logTx(outbound, 2 + outbound->getPathByteLen() + outbound->payload_len);
@@ -235,9 +272,20 @@ void Dispatcher::processRecvPacket(Packet* pkt) {
 }
 
 void Dispatcher::checkSend() {
-  if (_mgr->getOutboundCount(_ms->getMillis()) == 0) return;  // nothing waiting to send
-  if (!millisHasNowPassed(next_tx_time)) return;   // still in 'radio silence' phase (from airtime budget setting)
-  if (_radio->isReceiving()) {   // LBT - check if radio is currently mid-receive, or if channel activity
+  if (_mgr->getOutboundCount(_ms->getMillis()) == 0) return;
+  
+  updateTxBudget();
+  
+  uint32_t est_airtime = _radio->getEstAirtimeFor(MAX_TRANS_UNIT);
+  if (tx_budget_ms < est_airtime / MIN_TX_BUDGET_AIRTIME_DIV) {
+    float duty_cycle = 1.0f / (1.0f + getAirtimeBudgetFactor());
+    unsigned long needed = est_airtime / MIN_TX_BUDGET_AIRTIME_DIV - tx_budget_ms;
+    next_tx_time = futureMillis((unsigned long)(needed / duty_cycle));
+    return;
+  }
+  
+  if (!millisHasNowPassed(next_tx_time)) return;
+  if (_radio->isReceiving()) {
     if (cad_busy_start == 0) {
       cad_busy_start = _ms->getMillis();   // record when CAD busy state started
     }

src/Dispatcher.h

@@ -122,8 +122,12 @@ class Dispatcher {
   bool  prev_isrecv_mode;
   uint32_t n_sent_flood, n_sent_direct;
   uint32_t n_recv_flood, n_recv_direct;
+  unsigned long tx_budget_ms;
+  unsigned long last_budget_update;
+  unsigned long duty_cycle_window_ms;
 
   void processRecvPacket(Packet* pkt);
+  void updateTxBudget();
 
 protected:
   PacketManager* _mgr;
@@ -142,6 +146,9 @@ protected:
     _err_flags = 0;
     radio_nonrx_start = 0;
     prev_isrecv_mode = true;
+    tx_budget_ms = 0;
+    last_budget_update = 0;
+    duty_cycle_window_ms = 3600000;
   }
 
   virtual DispatcherAction onRecvPacket(Packet* pkt) = 0;
@@ -159,6 +166,7 @@ protected:
   virtual uint32_t getCADFailMaxDuration() const;
   virtual int getInterferenceThreshold() const { return 0; }    // disabled by default
   virtual int getAGCResetInterval() const { return 0; }    // disabled by default
+  virtual unsigned long getDutyCycleWindowMs() const { return 3600000; }
 
 public:
   void begin();
@@ -168,8 +176,9 @@ public:
   void releasePacket(Packet* packet);
   void sendPacket(Packet* packet, uint8_t priority, uint32_t delay_millis=0);
 
-  unsigned long getTotalAirTime() const { return total_air_time; }  // in milliseconds
+  unsigned long getTotalAirTime() const { return total_air_time; }
   unsigned long getReceiveAirTime() const {return rx_air_time; }
+  unsigned long getRemainingTxBudget() const { return tx_budget_ms; }
   uint32_t getNumSentFlood() const { return n_sent_flood; }
   uint32_t getNumSentDirect() const { return n_sent_direct; }
   uint32_t getNumRecvFlood() const { return n_recv_flood; }

src/helpers/CommonCLI.cpp

@@ -64,7 +64,8 @@ void CommonCLI::loadPrefsInt(FILESYSTEM* fs, const char* filename) {
     file.read((uint8_t *)&_prefs->bw, sizeof(_prefs->bw));                                         // 116
     file.read((uint8_t *)&_prefs->agc_reset_interval, sizeof(_prefs->agc_reset_interval));         // 120
     file.read((uint8_t *)&_prefs->path_hash_mode, sizeof(_prefs->path_hash_mode));                 // 121
-    file.read(pad, 2);                                                                             // 122
+    file.read((uint8_t *)&_prefs->loop_detect, sizeof(_prefs->loop_detect));                       // 122
+    file.read(pad, 1);                                                                             // 123
     file.read((uint8_t *)&_prefs->flood_max, sizeof(_prefs->flood_max));                           // 124
     file.read((uint8_t *)&_prefs->flood_advert_interval, sizeof(_prefs->flood_advert_interval));   // 125
     file.read((uint8_t *)&_prefs->interference_threshold, sizeof(_prefs->interference_threshold)); // 126
@@ -82,7 +83,9 @@ void CommonCLI::loadPrefsInt(FILESYSTEM* fs, const char* filename) {
     file.read((uint8_t *)&_prefs->discovery_mod_timestamp, sizeof(_prefs->discovery_mod_timestamp)); // 162
     file.read((uint8_t *)&_prefs->adc_multiplier, sizeof(_prefs->adc_multiplier)); // 166
     file.read((uint8_t *)_prefs->owner_info, sizeof(_prefs->owner_info));  // 170
-    // 290
+    file.read((uint8_t *)&_prefs->flood_advert_base, sizeof(_prefs->flood_advert_base));                 // 290
+
+    // 294
 
     // sanitise bad pref values
     _prefs->rx_delay_base = constrain(_prefs->rx_delay_base, 0, 20.0f);
@@ -110,6 +113,8 @@ void CommonCLI::loadPrefsInt(FILESYSTEM* fs, const char* filename) {
     _prefs->gps_enabled = constrain(_prefs->gps_enabled, 0, 1);
     _prefs->advert_loc_policy = constrain(_prefs->advert_loc_policy, 0, 2);
 
+    _prefs->flood_advert_base = constrain(_prefs->flood_advert_base, 0, 1);
+
     file.close();
   }
 }
@@ -150,7 +155,8 @@ void CommonCLI::savePrefs(FILESYSTEM* fs) {
     file.write((uint8_t *)&_prefs->bw, sizeof(_prefs->bw));                                         // 116
     file.write((uint8_t *)&_prefs->agc_reset_interval, sizeof(_prefs->agc_reset_interval));         // 120
     file.write((uint8_t *)&_prefs->path_hash_mode, sizeof(_prefs->path_hash_mode));                 // 121
-    file.write(pad, 2);                                                                             // 122
+    file.write((uint8_t *)&_prefs->loop_detect, sizeof(_prefs->loop_detect));                       // 122
+    file.write(pad, 1);                                                                             // 123
     file.write((uint8_t *)&_prefs->flood_max, sizeof(_prefs->flood_max));                           // 124
     file.write((uint8_t *)&_prefs->flood_advert_interval, sizeof(_prefs->flood_advert_interval));   // 125
     file.write((uint8_t *)&_prefs->interference_threshold, sizeof(_prefs->interference_threshold)); // 126
@@ -168,7 +174,9 @@ void CommonCLI::savePrefs(FILESYSTEM* fs) {
     file.write((uint8_t *)&_prefs->discovery_mod_timestamp, sizeof(_prefs->discovery_mod_timestamp)); // 162
     file.write((uint8_t *)&_prefs->adc_multiplier, sizeof(_prefs->adc_multiplier));                 // 166
     file.write((uint8_t *)_prefs->owner_info, sizeof(_prefs->owner_info));  // 170
-    // 290
+    file.write((uint8_t *)&_prefs->flood_advert_base, sizeof(_prefs->flood_advert_base));                 // 290
+
+    // 294
 
     file.close();
   }
@@ -203,6 +211,10 @@ void CommonCLI::handleCommand(uint32_t sender_timestamp, const char* command, ch
       // Reset clock
       getRTCClock()->setCurrentTime(1715770351);  // 15 May 2024, 8:50pm
       _board->reboot();  // doesn't return
+     } else if (memcmp(command, "advert.zerohop", 14) == 0 && (command[14] == 0 || command[14] == ' ')) {
+      // send zerohop advert
+      _callbacks->sendSelfAdvertisement(1500, false);  // longer delay, give CLI response time to be sent first
+      strcpy(reply, "OK - zerohop advert sent");
     } else if (memcmp(command, "advert", 6) == 0) {
       // send flood advert
       _callbacks->sendSelfAdvertisement(1500, true);  // longer delay, give CLI response time to be sent first
@@ -330,6 +342,16 @@ void CommonCLI::handleCommand(uint32_t sender_timestamp, const char* command, ch
         *reply = 0;  // set null terminator
       } else if (memcmp(config, "path.hash.mode", 14) == 0) {
         sprintf(reply, "> %d", (uint32_t)_prefs->path_hash_mode);
+      } else if (memcmp(config, "loop.detect", 11) == 0) {
+        if (_prefs->loop_detect == LOOP_DETECT_OFF) {
+          strcpy(reply, "> off");
+        } else if (_prefs->loop_detect == LOOP_DETECT_MINIMAL) {
+          strcpy(reply, "> minimal");
+        } else if (_prefs->loop_detect == LOOP_DETECT_MODERATE) {
+          strcpy(reply, "> moderate");
+        } else {
+          strcpy(reply, "> strict");
+        }
       } else if (memcmp(config, "tx", 2) == 0 && (config[2] == 0 || config[2] == ' ')) {
         sprintf(reply, "> %d", (int32_t) _prefs->tx_power_dbm);
       } else if (memcmp(config, "freq", 4) == 0) {
@@ -385,6 +407,8 @@ void CommonCLI::handleCommand(uint32_t sender_timestamp, const char* command, ch
         } else {
           sprintf(reply, "> %.3f", adc_mult);
         }
+      } else if (memcmp(config, "flood.advert.base", 17) == 0) {
+          sprintf(reply, "> %s", StrHelper::ftoa(_prefs->flood_advert_base));
       // Power management commands
       } else if (memcmp(config, "pwrmgt.support", 14) == 0) {
 #ifdef NRF52_POWER_MANAGEMENT
@@ -571,6 +595,26 @@ void CommonCLI::handleCommand(uint32_t sender_timestamp, const char* command, ch
         } else {
           strcpy(reply, "Error, must be 0,1, or 2");
         }
+      } else if (memcmp(config, "loop.detect ", 12) == 0) {
+        config += 12;
+        uint8_t mode;
+        if (memcmp(config, "off", 3) == 0) {
+          mode = LOOP_DETECT_OFF;
+        } else if (memcmp(config, "minimal", 7) == 0) {
+          mode = LOOP_DETECT_MINIMAL;
+        } else if (memcmp(config, "moderate", 8) == 0) {
+          mode = LOOP_DETECT_MODERATE;
+        } else if (memcmp(config, "strict", 6) == 0) {
+          mode = LOOP_DETECT_STRICT;
+        } else {
+          mode = 0xFF;
+          strcpy(reply, "Error, must be: off, minimal, moderate, or strict");
+        }
+        if (mode != 0xFF) {
+          _prefs->loop_detect = mode;
+          savePrefs();
+          strcpy(reply, "OK");
+        }
       } else if (memcmp(config, "tx ", 3) == 0) {
         _prefs->tx_power_dbm = atoi(&config[3]);
         savePrefs();
@@ -642,6 +686,15 @@ void CommonCLI::handleCommand(uint32_t sender_timestamp, const char* command, ch
           _prefs->adc_multiplier = 0.0f;
           strcpy(reply, "Error: unsupported by this board");
         };
+      } else if (memcmp(config, "flood.advert.base ", 18) == 0) {
+        float f = atof(&config[18]);
+        if(f >= 0 && f <= 1) {
+          _prefs->flood_advert_base = f;
+          savePrefs();
+          strcpy(reply, "OK");
+        } else {
+          strcpy(reply, "Error: base must be between 0 and 1");
+      }        
       } else {
         sprintf(reply, "unknown config: %s", config);
       }

src/helpers/CommonCLI.h

@@ -13,6 +13,11 @@
 #define ADVERT_LOC_SHARE      1
 #define ADVERT_LOC_PREFS      2
 
+#define LOOP_DETECT_OFF       0
+#define LOOP_DETECT_MINIMAL   1
+#define LOOP_DETECT_MODERATE  2
+#define LOOP_DETECT_STRICT    3
+
 struct NodePrefs { // persisted to file
   float airtime_factor;
   char node_name[32];
@@ -36,6 +41,7 @@ struct NodePrefs { // persisted to file
   uint8_t flood_max;
   uint8_t interference_threshold;
   uint8_t agc_reset_interval; // secs / 4
+  float flood_advert_base;
   // Bridge settings
   uint8_t bridge_enabled; // boolean
   uint16_t bridge_delay;  // milliseconds (default 500 ms)
@@ -53,6 +59,7 @@ struct NodePrefs { // persisted to file
   float adc_multiplier;
   char owner_info[120];
   uint8_t path_hash_mode;   // which path mode to use when sending
+  uint8_t loop_detect;
 };
 
 class CommonCLICallbacks {

src/helpers/sensors/EnvironmentSensorManager.cpp

@@ -683,7 +683,7 @@ void EnvironmentSensorManager::start_gps() {
   _location->begin();
   _location->reset();
 
-#ifndef PIN_GPS_RESET
+#ifndef PIN_GPS_EN
   MESH_DEBUG_PRINTLN("Start GPS is N/A on this board. Actual GPS state unchanged");
 #endif
 }

variants/ikoka_handheld_nrf/platformio.ini

@@ -1,5 +1,7 @@
 [ikoka_handheld_nrf]
 extends = nrf52_base
+board = seeed-xiao-afruitnrf52-nrf52840
+board_build.ldscript = boards/nrf52840_s140_v7.ld
 build_flags = ${nrf52_base.build_flags}
   ${sensor_base.build_flags}
   -I lib/nrf52/s140_nrf52_7.3.0_API/include
@@ -48,7 +50,8 @@ build_src_filter = ${ikoka_handheld_nrf.build_src_filter}
   +<../examples/companion_radio/*.cpp>
 
 [env:ikoka_handheld_nrf_e22_30dbm_096_companion_radio_ble]
-extends = ikoka_nrf52
+extends = ikoka_handheld_nrf
+board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld
 build_flags = ${ikoka_handheld_nrf_ssd1306_companion.build_flags}
   -D BLE_PIN_CODE=123456
   -D LORA_TX_POWER=20
@@ -56,7 +59,8 @@ build_src_filter = ${ikoka_handheld_nrf_ssd1306_companion.build_src_filter}
   +<helpers/nrf52/SerialBLEInterface.cpp>
 
 [env:ikoka_handheld_nrf_e22_30dbm_096_rotated_companion_radio_ble]
-extends = ikoka_nrf52
+extends = ikoka_handheld_nrf
+board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld
 build_flags = ${ikoka_handheld_nrf_ssd1306_companion.build_flags}
   -D BLE_PIN_CODE=123456
   -D LORA_TX_POWER=20
@@ -65,20 +69,22 @@ build_src_filter = ${ikoka_handheld_nrf_ssd1306_companion.build_src_filter}
   +<helpers/nrf52/SerialBLEInterface.cpp>
 
 [env:ikoka_handheld_nrf_e22_30dbm_096_companion_radio_usb]
-extends = ikoka_nrf52
+extends = ikoka_handheld_nrf
+board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld
 build_flags = ${ikoka_handheld_nrf_ssd1306_companion.build_flags}
   -D LORA_TX_POWER=20
 build_src_filter = ${ikoka_handheld_nrf_ssd1306_companion.build_src_filter}
 
 [env:ikoka_handheld_nrf_e22_30dbm_096_rotated_companion_radio_usb]
-extends = ikoka_nrf52
+extends = ikoka_handheld_nrf
+board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld
 build_flags = ${ikoka_handheld_nrf_ssd1306_companion.build_flags}
   -D LORA_TX_POWER=20
   -D DISPLAY_ROTATION=2
 build_src_filter = ${ikoka_handheld_nrf_ssd1306_companion.build_src_filter}
 
 [env:ikoka_handheld_nrf_e22_30dbm_repeater]
-extends = ikoka_nrf52
+extends = ikoka_handheld_nrf
 build_flags =
   ${ikoka_handheld_nrf.build_flags}
   -D ADVERT_NAME='"ikoka_handheld Repeater"'
@@ -91,7 +97,7 @@ build_src_filter = ${ikoka_handheld_nrf.build_src_filter}
   +<../examples/simple_repeater/*.cpp>
 
 [env:ikoka_handheld_nrf_e22_30dbm_room_server]
-extends = ikoka_nrf52
+extends = ikoka_handheld_nrf
 build_flags =
   ${ikoka_handheld_nrf.build_flags}
   -D ADVERT_NAME='"ikoka_handheld Room"'

variants/rak4631/variant.h

@@ -106,7 +106,7 @@ extern "C"
 
 // Power management boot protection threshold (millivolts)
 // Set to 0 to disable boot protection
-#define PWRMGT_VOLTAGE_BOOTLOCK 3300   // Won't boot below this voltage (mV)
+#define PWRMGT_VOLTAGE_BOOTLOCK 0   // Won't boot below this voltage (mV)
 // LPCOMP wake configuration (voltage recovery from SYSTEMOFF)
 // AIN3 = P0.05 = PIN_A0 / PIN_VBAT_READ
 #define PWRMGT_LPCOMP_AIN 3