rak4631, Xiao NRf, T114: set lockout voltage to 0V

examples/simple_repeater/MyMesh.cpp

@@ -546,7 +546,10 @@ bool MyMesh::filterRecvFloodPacket(mesh::Packet* pkt) {
   if (pkt->getRouteType() == ROUTE_TYPE_TRANSPORT_FLOOD) {
     recv_pkt_region = region_map.findMatch(pkt, REGION_DENY_FLOOD);
   } else if (pkt->getRouteType() == ROUTE_TYPE_FLOOD) {
-    if (region_map.getWildcard().flags & REGION_DENY_FLOOD) {
+      if ((pkt->getPayloadType() == PAYLOAD_TYPE_GRP_TXT ||
+           pkt->getPayloadType() == PAYLOAD_TYPE_GRP_DATA ||
+           pkt->getPayloadType() == PAYLOAD_TYPE_ADVERT) &&
+          region_map.getWildcard().flags & REGION_DENY_FLOOD) {
       recv_pkt_region = NULL;
     } else {
       recv_pkt_region =  &region_map.getWildcard();
@@ -878,7 +881,7 @@ MyMesh::MyMesh(mesh::MainBoard &board, mesh::Radio &radio, mesh::MillisecondCloc
   _prefs.cr = LORA_CR;
   _prefs.tx_power_dbm = LORA_TX_POWER;
   _prefs.advert_interval = 1;        // default to 2 minutes for NEW installs
-  _prefs.flood_advert_interval = 12; // 12 hours
+  _prefs.flood_advert_interval = 0; // 12 hours
   _prefs.flood_advert_base = 0.308f;
   _prefs.flood_max = 64;
   _prefs.interference_threshold = 0; // disabled

variants/heltec_t114/variant.h

@@ -32,7 +32,7 @@
 
 // Power management boot protection threshold (millivolts)
 // Set to 0 to disable boot protection
-#define PWRMGT_VOLTAGE_BOOTLOCK 3300   // Won't boot below this voltage (mV)
+#define PWRMGT_VOLTAGE_BOOTLOCK 0   // Won't boot below this voltage (mV)
 // LPCOMP wake configuration (voltage recovery from SYSTEMOFF)
 // AIN2 = P0.04 = BATTERY_PIN / PIN_VBAT_READ
 #define PWRMGT_LPCOMP_AIN 2

variants/rak4631/variant.h

@@ -106,7 +106,7 @@ extern "C"
 
 // Power management boot protection threshold (millivolts)
 // Set to 0 to disable boot protection
-#define PWRMGT_VOLTAGE_BOOTLOCK 3300   // Won't boot below this voltage (mV)
+#define PWRMGT_VOLTAGE_BOOTLOCK 0   // Won't boot below this voltage (mV)
 // LPCOMP wake configuration (voltage recovery from SYSTEMOFF)
 // AIN3 = P0.05 = PIN_A0 / PIN_VBAT_READ
 #define PWRMGT_LPCOMP_AIN 3

variants/xiao_nrf52/variant.h

@@ -77,7 +77,7 @@ static const uint8_t D10 = 10;
 
 // Power management boot protection threshold (millivolts)
 // Set to 0 to disable boot protection
-#define PWRMGT_VOLTAGE_BOOTLOCK    3300   // Won't boot below this voltage
+#define PWRMGT_VOLTAGE_BOOTLOCK    0   // Won't boot below this voltage
 
 // LPCOMP wake configuration (voltage recovery from SYSTEMOFF)
 #define PWRMGT_LPCOMP_AIN           7     // AIN7 = P0.31 = PIN_VBAT