Adopts hardware Channel Activity Detection (wired into
RadioLibWrapper::isChannelActive() alongside our RSSI-threshold check
and RX duty-cycle power-save), MCU temperature telemetry, LR2021
standby workaround, DISPLAY_SCALE/FLIP overrides, NRF52Board
shutdownPeripherals() refactor, and misc upstream fixes.
Declines upstream's ConfigSerializer-based NodePrefs rewrite,
MultiSerialInterface/interface_manager, and UIColor palette system —
each would have broken large parts of the Solo-specific feature set
(NodePrefs fields, per-variant single serial_interface, enum-based
DisplayDriver::Color). Flagged as candidate follow-up migrations, not
permanent no's.
Also fixes several pre-existing bugs surfaced while chasing silent
merge breaks (stale newMsg() override signature in ui-tiny/ui-orig,
dead UIEventType::newContactMessage case, missing ContactsIterator
init), bumps FIRMWARE_VERSION/MESHCORE_VERSION to 1.17, and fixes a
missing <cstdlib> include that broke the native ConfigSerializer unit
tests.
Verified via 13+ pio run builds across ESP32/nRF52, all 3 companion UI
variants, and 7 display drivers, plus the full native unit test suite
(33/33 passing).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The solo release job only attached *.uf2 and *.zip, which covered every solo
board back when they were all nRF52. The Heltec V3/V4 .bin images were built
and then silently dropped, so tagging a release produced nothing downloadable
for those two boards.
Releases now carry a single -merged.bin per ESP32 board (bootloader +
partition table + app at 0x0). build.sh also writes an app-only .bin, but
that one needs offset 0x10000 and a bootloader already on the chip, so it's
deleted before upload rather than shipped next to the merged image — flashing
it at 0x0 looks exactly like a bricked device.
Also adds -D ENABLE_SCREENSHOT to both Heltec solo envs. Every other solo env
already had it, so Solo Tools couldn't capture these two boards' displays and
the README's "no special build flags required" was untrue for them. Both envs
rebuilt clean (V3: RAM 58.8%, Flash 43.2%).
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Port the Wio Tracker L1 solo firmware (full on-device UI, dual BLE/USB
companion transport) to Heltec V3 and V4 OLED boards. Neither board has
a joystick or CardKB on-board, so each new env wires up both as optional
peripherals with default pins from what the board leaves free, gated
behind the existing UI_HAS_JOYSTICK/ENV_PIN_SDA+SCL flags.
DUAL_SERIAL was nRF52-only; added an ESP32 helpers/esp32/DualSerialInterface.h
counterpart so the flag isn't silently ignored on these boards. On V4's
native USB CDC, isClientConnected() also honours (bool)Serial (real DTR),
same as the nRF52 version; V3 has no native CDC so it stays BLE-only there.
Screen (SDA 17/SCL 18) and CardKB (SDA 3/SCL 4) confirmed working on real
V4 hardware.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Switch ESP32-S3 KISS modem environments to HWCDC and move outbound KISS writes to a non-blocking queued frame path so loop() and TX completion keep progressing when the host reads slowly. Add native backpressure regression tests and correct the native_kiss_modem test filter so this suite runs directly with pio test.
JakubandClaude Sonnet 5
liamcottle
ViezeVingertjes
Rastislav Vysoky
Kevin Le
ripplebizandGitHub
João Brázio
Quency-DandGitHub
Quency-D
Oliver Weyhmüller
SoCalixandGitHub
Luke
Scott Powell
fdlamotteandGitHub