Mirrors/MeshCore-Solo
1
0
Fork 0
mirror of https://github.com/MarekZegare4/MeshCore-Solo.git synced 2026-08-07 20:56:11 +00:00
Code Issues Packages Projects Releases Wiki Activity
Files
2bde84a5731181a538c623faa68301b07118e487
MeshCore-Solo/variants/heltec_v4/platformio.ini
T
JakubandClaude Sonnet 5 2bde84a573 feat(heltec): solo dual-transport builds for Heltec V3/V4 
Port the Wio Tracker L1 solo firmware (full on-device UI, dual BLE/USB
companion transport) to Heltec V3 and V4 OLED boards. Neither board has
a joystick or CardKB on-board, so each new env wires up both as optional
peripherals with default pins from what the board leaves free, gated
behind the existing UI_HAS_JOYSTICK/ENV_PIN_SDA+SCL flags.

DUAL_SERIAL was nRF52-only; added an ESP32 helpers/esp32/DualSerialInterface.h
counterpart so the flag isn't silently ignored on these boards. On V4's
native USB CDC, isClientConnected() also honours (bool)Serial (real DTR),
same as the nRF52 version; V3 has no native CDC so it stays BLE-only there.

Screen (SDA 17/SCL 18) and CardKB (SDA 3/SCL 4) confirmed working on real
V4 hardware.

Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
2026-08-06 20:08:31 +02:00

521 lines
16 KiB
INI
Raw Blame History

[Heltec_lora32_v4]
extends = esp32_base
board = heltec_v4
build_flags =
${esp32_base.build_flags}
${sensor_base.build_flags}
-I variants/heltec_v4
-D HELTEC_LORA_V4
-D USE_SX1262
-D ESP32_CPU_FREQ=80
-D RADIO_CLASS=CustomSX1262
-D WRAPPER_CLASS=CustomSX1262Wrapper
-D P_LORA_TX_LED=35
-D P_LORA_DIO_1=14
-D P_LORA_NSS=8
-D P_LORA_RESET=12
-D P_LORA_BUSY=13
-D P_LORA_SCLK=9
-D P_LORA_MISO=11
-D P_LORA_MOSI=10
-D P_LORA_PA_POWER=7 ; // VFEM_Ctrl -LDO power enable
-D P_LORA_GC1109_PA_EN=2 ; // CSD - GC1109 chip enable (HIGH=on)
-D P_LORA_GC1109_PA_TX_EN=46 ;// CPS - GC1109 PA mode (HIGH=full PA, LOW=bypass)
-D P_LORA_KCT8103L_PA_CSD=2
-D P_LORA_KCT8103L_PA_CTX=5
-D PIN_USER_BTN=0
-D PIN_VEXT_EN=36
-D PIN_VEXT_EN_ACTIVE=HIGH
-D LORA_TX_POWER=10 ;If it is configured as 10 here, the final output will be 22 dbm.
-D MAX_LORA_TX_POWER=22 ; Max SX1262 output
-D SX126X_REGISTER_PATCH=1 ; Patch register 0x8B5 for improved RX
-D SX126X_DIO2_AS_RF_SWITCH=true ; GC1109 CTX is controlled by SX1262 DIO2
-D SX126X_DIO3_TCXO_VOLTAGE=1.8
-D SX126X_CURRENT_LIMIT=140
-D SX126X_RX_BOOSTED_GAIN=1 ; In some cases, commenting this out will improve RX
-D PIN_GPS_RX=38
-D PIN_GPS_TX=39
-D PIN_GPS_RESET=42
-D PIN_GPS_RESET_ACTIVE=LOW
-D PIN_GPS_EN=34
-D PIN_GPS_EN_ACTIVE=LOW
-D ENV_INCLUDE_GPS=1
-D PIN_ADC_CTRL=37
-D PIN_VBAT_READ=1
build_src_filter = ${esp32_base.build_src_filter}
+<../variants/heltec_v4>
+<helpers/sensors>
lib_deps =
${esp32_base.lib_deps}
${sensor_base.lib_deps}
[heltec_v4_oled]
extends = Heltec_lora32_v4
build_flags =
${Heltec_lora32_v4.build_flags}
-D HELTEC_LORA_V4_OLED
-D PIN_BOARD_SDA=17
-D PIN_BOARD_SCL=18
-D PIN_OLED_RESET=21
build_src_filter= ${Heltec_lora32_v4.build_src_filter}
lib_deps = ${Heltec_lora32_v4.lib_deps}
[heltec_v4_tft]
extends = Heltec_lora32_v4
build_flags =
${Heltec_lora32_v4.build_flags}
-D HELTEC_LORA_V4_TFT
-D PIN_BOARD_SDA=4
-D PIN_BOARD_SCL=3
-D DISPLAY_SCALE_X=2.5
-D DISPLAY_SCALE_Y=3.75
-D PIN_TFT_RST=18
-D PIN_TFT_VDD_CTL=-1
-D PIN_TFT_LEDA_CTL=21
-D PIN_TFT_LEDA_CTL_ACTIVE=HIGH
-D PIN_TFT_CS=15
-D PIN_TFT_DC=16
-D PIN_TFT_SCL=17
-D PIN_TFT_SDA=33
build_src_filter= ${Heltec_lora32_v4.build_src_filter}
lib_deps =
${Heltec_lora32_v4.lib_deps}
adafruit/Adafruit ST7735 and ST7789 Library @ ^1.11.0
[env:heltec_v4_repeater]
extends = heltec_v4_oled
build_flags =
${heltec_v4_oled.build_flags}
-D DISPLAY_CLASS=SSD1306Display
-D ADVERT_NAME='"Heltec Repeater"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_oled.build_src_filter}
+<helpers/ui/SSD1306Display.cpp>
+<../examples/simple_repeater>
lib_deps =
${heltec_v4_oled.lib_deps}
${esp32_ota.lib_deps}
bakercp/CRC32 @ ^2.0.0
[env:heltec_v4_expansionkit_repeater]
extends = heltec_v4_oled
build_flags =
${heltec_v4_oled.build_flags}
-D DISPLAY_CLASS=SSD1306Display
-D ADVERT_NAME='"Heltec Repeater"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
-D ENV_PIN_SDA=4
-D ENV_PIN_SCL=3
build_src_filter = ${heltec_v4_oled.build_src_filter}
+<helpers/ui/SSD1306Display.cpp>
+<../examples/simple_repeater>
lib_deps =
${heltec_v4_oled.lib_deps}
${esp32_ota.lib_deps}
bakercp/CRC32 @ ^2.0.0
[env:heltec_v4_repeater_bridge_espnow]
extends = heltec_v4_oled
build_flags =
${heltec_v4_oled.build_flags}
-D DISPLAY_CLASS=SSD1306Display
-D ADVERT_NAME='"ESPNow Bridge"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
-D WITH_ESPNOW_BRIDGE=1
; -D BRIDGE_DEBUG=1
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_oled.build_src_filter}
+<helpers/bridges/ESPNowBridge.cpp>
+<helpers/ui/SSD1306Display.cpp>
+<../examples/simple_repeater>
lib_deps =
${heltec_v4_oled.lib_deps}
${esp32_ota.lib_deps}
[env:heltec_v4_room_server]
extends = heltec_v4_oled
build_flags =
${heltec_v4_oled.build_flags}
-D DISPLAY_CLASS=SSD1306Display
-D ADVERT_NAME='"Heltec Room"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D ROOM_PASSWORD='"hello"'
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_oled.build_src_filter}
+<helpers/ui/SSD1306Display.cpp>
+<../examples/simple_room_server>
lib_deps =
${heltec_v4_oled.lib_deps}
${esp32_ota.lib_deps}
[env:heltec_v4_terminal_chat]
extends = heltec_v4_oled
build_flags =
${heltec_v4_oled.build_flags}
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=1
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_oled.build_src_filter}
+<../examples/simple_secure_chat/main.cpp>
lib_deps =
${heltec_v4_oled.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:heltec_v4_companion_radio_usb]
extends = heltec_v4_oled
build_flags =
${heltec_v4_oled.build_flags}
-I examples/companion_radio/ui-new
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D DISPLAY_CLASS=SSD1306Display
; NOTE: DO NOT ENABLE --> -D MESH_PACKET_LOGGING=1
; NOTE: DO NOT ENABLE --> -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_oled.build_src_filter}
+<helpers/ui/SSD1306Display.cpp>
+<helpers/ui/MomentaryButton.cpp>
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${heltec_v4_oled.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:heltec_v4_companion_radio_ble]
extends = heltec_v4_oled
build_flags =
${heltec_v4_oled.build_flags}
-I examples/companion_radio/ui-new
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D DISPLAY_CLASS=SSD1306Display
-D BLE_PIN_CODE=123456 ; dynamic, random PIN
-D AUTO_SHUTDOWN_MILLIVOLTS=3400
-D BLE_DEBUG_LOGGING=1
-D OFFLINE_QUEUE_SIZE=256
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_oled.build_src_filter}
+<helpers/ui/SSD1306Display.cpp>
+<helpers/ui/MomentaryButton.cpp>
+<helpers/esp32/*.cpp>
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${heltec_v4_oled.lib_deps}
densaugeo/base64 @ ~1.4.0
; Solo build: the full standalone on-device UI (message history, contacts, map,
; tools) rather than a screen that only mirrors the phone app. Dual transport --
; the companion app can attach over BLE or USB serial, whichever it finds, and
; BLE wins while both are live. OLED board only -- the TFT variant would need
; its own DISPLAY_CLASS.
;
; This firmware needs a real input device: the solo UI cannot be driven from the
; PRG button alone. Both supported ones are wired up in target.cpp and enabled
; below, so either is enough on its own and having both is fine. The pins are
; defaults picked from what this board leaves free -- change them to match how
; the device is actually built. Pins with nothing attached read as not-pressed,
; so the unused half costs nothing.
;
; * CardKB (M5Stack I2C keyboard, addr 0x5F) on a second I2C bus. Any two free
; GPIOs -- NOT 17/18, the OLED already owns those on Wire. It's probed at
; boot, so a build with these set still runs fine with nothing plugged in.
; Pair it with Settings > Keyboard > Ext. KB = Compact, which is designed to
; need no joystick at all. The same bus is scanned for environment sensors.
; Defaults below: SDA 3, SCL 4 -- the pins heltec_v4_sensor and
; heltec_v4_expansionkit_repeater already use for their second I2C bus, i.e.
; the expansion kit's. (Those envs disagree on the order: two say SDA 3 /
; SCL 4, one says the reverse. 3/4 is the pair either way; swap them if the
; keyboard doesn't answer.)
;
; * Wired joystick: four direction pins plus a separate Back button -- the UI
; uses Back unconditionally once UI_HAS_JOYSTICK is set, so it isn't optional.
; PIN_USER_BTN (PRG) stays the centre/Enter press. Each contact just shorts
; its pin to GND; target.cpp enables the internal pull-ups. Drop
; UI_HAS_JOYSTICK_UPDOWN for a left/right-only stick. JOYSTICK_ROTATION (0-3)
; rotates the mapping if the stick is mounted sideways -- it's also a runtime
; setting, so leave it out unless you want a different default.
; Comment the whole block out for a CardKB-only build. UI_HAS_JOYSTICK
; replaces the single-button handling rather than adding to it (UITask.cpp
; dispatches on '#if UI_HAS_JOYSTICK ... #elif defined(PIN_USER_BTN)'), which
; costs nothing here -- that fallback only feeds KEY_NEXT/KEY_PREV, which the
; solo screens don't act on.
;
; Free on this board, per its pinout: 3, 4, 6, 23, 33, 43, 44, 45, 46, 47, 48.
; Two of those can't take an I2C pull-up: 45 selects VDD_SPI at boot, so held
; high the chip comes up expecting 1.8V flash and won't boot at all, and 46 is
; the boot-mode strap. 3 is a strapping pin too, but it only picks the JTAG
; source -- and it's what this board's own expansion kit uses for I2C anyway.
; 43/44 are UART0: unused by this build, since ARDUINO_USB_CDC_ON_BOOT (set in
; boards/heltec_v4.json) makes Serial the native USB port, but a USB-UART bridge
; may still be wired to them, so they're left alone.
[env:heltec_v4_companion_solo_dual]
extends = heltec_v4_oled
build_flags =
${heltec_v4_oled.build_flags}
-I examples/companion_radio/ui-new
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D DISPLAY_CLASS=SSD1306Display
-D BLE_PIN_CODE=123456 ; dynamic, random PIN
-D DUAL_SERIAL=1 ; companion app over BLE *or* USB serial
-D AUTO_SHUTDOWN_MILLIVOLTS=3400
-D OFFLINE_QUEUE_SIZE=256
-D FIRMWARE_SOLO_BUILD=1
-D UI_SENSORS_PAGE=1
-D OLED_MISC_FIXED_FONT=1 ; full Latin/Greek/Cyrillic 6x9 font, ~14 KB flash
; CardKB on the second I2C bus. Harmless with nothing plugged in.
-D ENV_PIN_SDA=3
-D ENV_PIN_SCL=4
; Wired joystick — comment the block out for a CardKB-only build.
-D UI_HAS_JOYSTICK=1
-D UI_HAS_JOYSTICK_UPDOWN=1
-D JOYSTICK_UP=23
-D JOYSTICK_DOWN=6
-D JOYSTICK_LEFT=47
-D JOYSTICK_RIGHT=48
-D PIN_BACK_BTN=33
; -D PIN_BUZZER=<gpio>
build_src_filter = ${heltec_v4_oled.build_src_filter}
+<helpers/ui/SSD1306Display.cpp>
+<helpers/ui/MomentaryButton.cpp>
+<helpers/ui/buzzer.cpp>
+<helpers/esp32/*.cpp>
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${heltec_v4_oled.lib_deps}
densaugeo/base64 @ ~1.4.0
end2endzone/NonBlockingRTTTL@^1.3.0
[env:heltec_v4_companion_radio_wifi]
extends = heltec_v4_oled
build_flags =
${heltec_v4_oled.build_flags}
-I examples/companion_radio/ui-new
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D OFFLINE_QUEUE_SIZE=256
-D DISPLAY_CLASS=SSD1306Display
-D WIFI_DEBUG_LOGGING=1
-D WIFI_SSID='"myssid"'
-D WIFI_PWD='"mypwd"'
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_oled.build_src_filter}
+<helpers/ui/SSD1306Display.cpp>
+<helpers/ui/MomentaryButton.cpp>
+<helpers/esp32/*.cpp>
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${heltec_v4_oled.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:heltec_v4_sensor]
extends = heltec_v4_oled
build_flags =
${heltec_v4_oled.build_flags}
-D ADVERT_NAME='"Heltec v4 Sensor"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D ENV_PIN_SDA=3
-D ENV_PIN_SCL=4
-D DISPLAY_CLASS=SSD1306Display
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_oled.build_src_filter}
+<helpers/ui/SSD1306Display.cpp>
+<../examples/simple_sensor>
lib_deps =
${heltec_v4_oled.lib_deps}
${esp32_ota.lib_deps}
[env:heltec_v4_tft_repeater]
extends = heltec_v4_tft
build_flags =
${heltec_v4_tft.build_flags}
-D DISPLAY_CLASS=ST7789LCDDisplay
-D ADVERT_NAME='"Heltec Repeater"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_tft.build_src_filter}
+<helpers/ui/ST7789LCDDisplay.cpp>
+<../examples/simple_repeater>
lib_deps =
${heltec_v4_tft.lib_deps}
${esp32_ota.lib_deps}
bakercp/CRC32 @ ^2.0.0
[env:heltec_v4_tft_repeater_bridge_espnow]
extends = heltec_v4_tft
build_flags =
${heltec_v4_tft.build_flags}
-D DISPLAY_CLASS=ST7789LCDDisplay
-D ADVERT_NAME='"ESPNow Bridge"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D MAX_NEIGHBOURS=50
-D WITH_ESPNOW_BRIDGE=1
; -D BRIDGE_DEBUG=1
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_tft.build_src_filter}
+<helpers/bridges/ESPNowBridge.cpp>
+<helpers/ui/ST7789LCDDisplay.cpp>
+<../examples/simple_repeater>
lib_deps =
${heltec_v4_tft.lib_deps}
${esp32_ota.lib_deps}
[env:heltec_v4_tft_room_server]
extends = heltec_v4_tft
build_flags =
${heltec_v4_tft.build_flags}
-D DISPLAY_CLASS=ST7789LCDDisplay
-D ADVERT_NAME='"Heltec Room"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D ROOM_PASSWORD='"hello"'
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_tft.build_src_filter}
+<helpers/ui/ST7789LCDDisplay.cpp>
+<../examples/simple_room_server>
lib_deps =
${heltec_v4_tft.lib_deps}
${esp32_ota.lib_deps}
[env:heltec_v4_tft_terminal_chat]
extends = heltec_v4_tft
build_flags =
${heltec_v4_tft.build_flags}
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=1
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_tft.build_src_filter}
+<../examples/simple_secure_chat/main.cpp>
lib_deps =
${heltec_v4_tft.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:heltec_v4_tft_companion_radio_usb]
extends = heltec_v4_tft
build_flags =
${heltec_v4_tft.build_flags}
-I examples/companion_radio/ui-new
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D DISPLAY_CLASS=ST7789LCDDisplay
; NOTE: DO NOT ENABLE --> -D MESH_PACKET_LOGGING=1
; NOTE: DO NOT ENABLE --> -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_tft.build_src_filter}
+<helpers/ui/ST7789LCDDisplay.cpp>
+<helpers/ui/MomentaryButton.cpp>
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${heltec_v4_tft.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:heltec_v4_tft_companion_radio_ble]
extends = heltec_v4_tft
build_flags =
${heltec_v4_tft.build_flags}
-I examples/companion_radio/ui-new
-D DISPLAY_CLASS=ST7789LCDDisplay
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D BLE_PIN_CODE=123456 ; dynamic, random PIN
-D AUTO_SHUTDOWN_MILLIVOLTS=3400
-D BLE_DEBUG_LOGGING=1
-D OFFLINE_QUEUE_SIZE=256
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_tft.build_src_filter}
+<helpers/ui/ST7789LCDDisplay.cpp>
+<helpers/ui/MomentaryButton.cpp>
+<helpers/esp32/*.cpp>
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${heltec_v4_tft.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:heltec_v4_tft_companion_radio_wifi]
extends = heltec_v4_tft
build_flags =
${heltec_v4_tft.build_flags}
-I examples/companion_radio/ui-new
-D MAX_CONTACTS=350
-D MAX_GROUP_CHANNELS=40
-D OFFLINE_QUEUE_SIZE=256
-D DISPLAY_CLASS=ST7789LCDDisplay
-D WIFI_DEBUG_LOGGING=1
-D WIFI_SSID='"myssid"'
-D WIFI_PWD='"mypwd"'
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_tft.build_src_filter}
+<helpers/ui/ST7789LCDDisplay.cpp>
+<helpers/ui/MomentaryButton.cpp>
+<helpers/esp32/*.cpp>
+<../examples/companion_radio/*.cpp>
+<../examples/companion_radio/ui-new/*.cpp>
lib_deps =
${heltec_v4_tft.lib_deps}
densaugeo/base64 @ ~1.4.0
[env:heltec_v4_tft_sensor]
extends = heltec_v4_tft
build_flags =
${heltec_v4_tft.build_flags}
-D ADVERT_NAME='"Heltec v4 Sensor"'
-D ADVERT_LAT=0.0
-D ADVERT_LON=0.0
-D ADMIN_PASSWORD='"password"'
-D ENV_PIN_SDA=3
-D ENV_PIN_SCL=4
-D DISPLAY_CLASS=ST7789LCDDisplay
; -D MESH_PACKET_LOGGING=1
; -D MESH_DEBUG=1
build_src_filter = ${heltec_v4_tft.build_src_filter}
+<helpers/ui/ST7789LCDDisplay.cpp>
+<../examples/simple_sensor>
lib_deps =
${heltec_v4_tft.lib_deps}
${esp32_ota.lib_deps}
[env:heltec_v4_kiss_modem]
extends = Heltec_lora32_v4
build_src_filter = ${Heltec_lora32_v4.build_src_filter}
+<../examples/kiss_modem/>
Reference in New Issue View Git Blame Copy Permalink