Tables for all seven sections (Display, Sound, Home Pages, Radio, System,
Contacts, Messages) with values, LEFT/RIGHT vs Enter interaction, and
e-ink-only flags. Notes: buzzer Auto mode, battery % anchor from low_batt,
Melody 1/2 link to Ringtone Editor, placeholder support in quick replies.
msgRead(0) was called when the companion app read the last message from
the offline queue, and it erased the entire _dm_unread_table. This wiped
Favourites Dial badges the moment the app synced — leaving a 3-second
window (the alert duration) where the badge was faintly visible behind
the incoming-message popup, then gone.
_dm_unread_table tracks per-contact UI state (Favourites Dial badges,
contact list counters). It should only be cleared by user action:
clearDMUnread (opens a DM) or clearAllDMUnread (mark-all-read). It has
no relationship to the offline queue drain state.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
When the user presses + on an empty Favourites Dial tile, the picker
previously showed 'No fav contacts' if there were no starred contacts
(flags & 0x01) AND no recent DMs in _dm_hist (empty after reboot).
Add a third fallback tier: when the first two tiers yield nothing, list
all ADV_TYPE_CHAT contacts so the user can always pin anyone. Alert
text updated to 'No contacts' for the remaining edge case (no contacts
at all in the mesh).
Known limitation: per-contact unread badges on the dial reset on reboot
(in-RAM only). Persisted unread is a separate future improvement.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- Describe 2×3 portrait vs 3×2 landscape grid layout
- Navigation: edge keys fall through to page nav
- Unread badge detail (ellipsis + badge coexistence)
- (gone) label for removed contacts
- Two pinning paths: empty tile picker and DM context menu
- Pin picker order: favourited contacts first, then recent DMs
- Auto-move when contact already pinned elsewhere
- Unpin via DM context menu
- Reordering via Settings › Home Pages
- Describe DM/Channels/Rooms mode-select
- Describe MSG_PICK flow (keyboard vs quick replies Q1-Q10)
- Complete placeholder table — remove {batt} (shows in picker only
when a voltage sensor is connected, not from board battery)
- Separate contact and channel context menus with full item tables
- Document LEFT/RIGHT cycling for Notif/Melody/Fav
- Describe Pin to dial with slot picker detail
- Clarify short Enter (fullscreen) vs Hold Enter (context menu)
- Add fullscreen navigation and scroll description
PopupMenu:
- _cap now uses max_by_height as a hard ceiling (never draw outside screen).
Previously max(_visible, max_by_height) let callers exceed the screen on
OLED 64px. Now: OLED→4 items, landscape e-ink→10, portrait e-ink→22.
QuickMsgScreen:
- Contact context menu: Notif and Melody cycle with LEFT/RIGHT in-place;
ENTER closes without re-cycling.
- Channel context menu: Notif, Melody and Fav same pattern.
RingtoneEditorScreen:
- Migrated from bespoke menu to PopupMenu (same pattern as everywhere else).
- Duration (1/4…1/32) and BPM (60…180) are now single rows that cycle with
LEFT/RIGHT; separate BPM+/BPM- rows removed.
- Fixed _menu_dur_label buffer too small for "Duration: 1/16" (14→16 bytes).
NearbyScreen:
- Removed redundant "Back" item from context menu (Cancel key navigates back).
TrailScreen:
- Grid toggle responds to LEFT/RIGHT in addition to ENTER.
- Export labels: "Export GPX (live/saved)" → "Export (live/saved)" to fit PM_BW.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
'Export GPX' and 'Export saved' were ambiguous. Renamed to
'Export GPX (live)' (RAM ring) and 'Export GPX (saved)' (flash file)
so the source of each export is immediately clear.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
On a 250px-tall portrait e-ink panel the menu previously showed only 3-4
items and required scrolling. render() now computes the maximum items that
fit from display.height() and uses that instead of the hardcoded caller
hint whenever the screen is taller. handleInput() uses the same _cap value
so scroll tracking stays in sync.
OLED (64px): fits 4 items — unchanged behaviour.
Portrait e-ink (250px): fits up to 22 items (capped at PM_MAX_ITEMS=16),
no scroll needed for typical context menus (4-6 items).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Adds GxEPD2 framebuffer capture to the screenshot tool, extending the
existing OLED support to the Wio Tracker L1 e-ink variant.
Key changes:
- GxEPD2-patch: patched copy of GxEPD2_BW.h exposing getBuffer/getBufferSize
- GxEPDDisplay: override getBuffer/getBufferSize/getDisplayType/
screenshotWidth/screenshotHeight/screenshotRotation using GxEPD2's
own reported visible dimensions (WIDTH_VISIBLE, not physical WIDTH)
and live rotation value
- DisplayDriver: virtual screenshot interface so no C-style casts needed
- Protocol: 11-byte header with display_type, rotation, uint16 LE
width/height/chunk_idx/total_chunks (eliminates truncation for panels >255px)
- screenshot.py: full rot 0-3 decoder for GxEPD2 buffer layout; ERR frame
checked before length so device errors surface correctly; buffer-size
sanity check using panel-aware expected size
Conflict resolution: kept feat/eink-screenshot protocol and decoder
(11-byte header, e-ink decode) over the OLED-only 5-byte version on
wio-unified; battery and joystick fixes from wio-unified kept intact.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
handleScreenshotRequest() reinterpret-cast every DisplayDriver* first to
SH1106Display* then to SSD1306Display*; both casts always produce a
non-null pointer, so the SSD1306 fallback was unreachable and on any
SSD1306 build we called SH1106::getBuffer() on a SSD1306 object — UB
that only happened to work because both backing classes share an
Adafruit_GFX layout at offset zero.
Replace the cast hack with virtual getBuffer()/getBufferSize() on
DisplayDriver, overridden in SH1106Display and SSD1306Display. MyMesh
no longer needs to know about either concrete type. const-correct the
buffer pointer and widen bufferSize to uint16_t while passing through.
Also fix the matching Python decoder: it sanity-checked length before
dispatching on resp_code, so a 2-byte RESP_CODE_ERR frame was reported
as "Frame too short" instead of the actual device error. Move the
length check after the resp_code dispatch and log the error code byte.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
The Clock-page Batt% field used a separate hardcoded linear mapping
(3000-4200 mV → 0-100%) that disagreed with the top-bar battery indicator,
which uses a piecewise LiPo discharge curve and the user-configurable
low_batt_mv cutoff (Settings → Low battery threshold) as the 0% anchor.
The two readings could differ by 25+ percentage points for the same
voltage, and the dashboard ignored the cutoff setting entirely.
Extract battMvToPercent(mv, low_mv) as a file-static helper so both the
top-bar indicator and the dashboard field share the same curve and the
same cutoff source. Drop the stray BATT_MIN/MAX_MILLIVOLTS #defines
that leaked from inside the dashboard code paths into the rest of the
TU.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
Firmware (7-byte header):
Byte 7 = display->screenshotRotation() — GxEPD2/GFX rotation value (0-3).
DisplayDriver::screenshotRotation() defaults to 0 (OLED).
GxEPDDisplay::screenshotRotation() returns display.getRotation(), the
live GxEPD2 value (reflects runtime setDisplayRotation() calls, not just
the compile-time DISPLAY_ROTATION macro).
Python decoder:
- Parse 7-byte header; pass rotation to eink_buffer_to_image().
- Implement all four GxEPD2 drawPixel coordinate transforms:
rot 0: phys_x=lx, phys_y=ly
rot 1: phys_x=vis_w-1-ly, phys_y=lx
rot 2: phys_x=vis_w-1-lx, phys_y=vis_h-1-ly (180° flip)
rot 3: phys_x=ly, phys_y=vis_h-1-lx
- vis_w/vis_h derived from log dimensions + rotation parity (no constants).
- Print rot= in the status line so the user sees which rotation was used.
This fixes the 180° rotated image seen with rotation=2 (portrait inverted)
without hardcoding a flip — correct for any rotation value.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
The previous decoder always applied the rotation=1 (landscape) transform,
which caused three visible artefacts on a portrait (rotation=0) device:
- Content rotated 90° — wrong phys_x/phys_y mapping
- Content doubled/skewed — stride = buffer/log_width = 4000/122 = 32
instead of buffer/HEIGHT = 4000/250 = 16
Fix: infer rotation from aspect ratio (portrait: log_height > log_width).
portrait → direct mapping: phys_x=lx, phys_y=ly
landscape → rotation-1 map: phys_x=log_height-1-ly, phys_y=lx
Derive phys_stride from buffer_size // max(log_w, log_h) — the physical
HEIGHT is always the longer axis regardless of rotation, giving 16 bytes/row
for GxEPD2_213_B74 in both orientations.
No panel-specific constants remain; works for any GxEPD2 panel/rotation.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Firmware: add screenshotWidth()/screenshotHeight() virtual pair to
DisplayDriver (default: width()/height()). GxEPDDisplay overrides to
return display.width()/display.height() — the GxEPD2-reported values
that use WIDTH_VISIBLE (e.g. 122 for GxEPD2_213_B74), not the full
physical WIDTH stored in DisplayDriver (128). MyMesh uses these
instead of display->width()/height() for the screenshot header bytes.
Result for GxEPD2_213_B74 + DISPLAY_ROTATION=1:
header was 250×128 → now 250×122 (correct visible canvas)
Python decoder (tools/screenshot.py):
- Remove hardcoded EINK_PHYS_WIDTH=128 / EINK_VISIBLE_W=122 constants.
- Derive phys_stride from buffer_size / log_width (works for any panel).
- Fix phys_x formula: was (EINK_PHYS_WIDTH-1-ly = 127-ly),
now (vis_w-1-ly = log_height-1-ly = 121-ly for 213_B74).
Old formula addressed invisible columns 122-127; new formula correctly
maps logical rows 0..121 to visible physical columns 121..0.
- vis_w = log_height (no hardcoded trim; header now carries correct value).
This also works for square panels (e.g. 128×128 where WIDTH=WIDTH_VISIBLE):
header will carry 128×128, decoder produces a correct 128×128 image.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- Add lib/GxEPD2-patch/src/GxEPD2_BW.h: local patched copy of GxEPD2_BW.h
that exposes getBuffer()/getBufferSize() under ENABLE_SCREENSHOT guard.
Include guard (_GxEPD2_BW_H_) prevents double-inclusion of the installed
library version.
- GxEPDDisplay.h: use patched header via relative include when
ENABLE_SCREENSHOT so the patch takes precedence over the installed lib
(PlatformIO adds library paths before -I build_flags).
- DisplayDriver.h: add virtual getBuffer()/getBufferSize()/getDisplayType()
defaults (nullptr/0/0) under ENABLE_SCREENSHOT.
- SH1106Display.h / SSD1306Display.h / GxEPDDisplay.h: add concrete overrides;
getDisplayType() returns 0 (OLED) or 1 (e-ink).
- MyMesh.cpp/h: replace fragile C-cast with virtual dispatch in
handleScreenshotRequest(); extend 5-byte header to 6 bytes by appending
display_type so the host tool can decode the correct pixel layout.
- tools/screenshot.py: parse 6-byte header; add eink_buffer_to_image()
that decodes the row-major MSB-first GxEPD2 buffer with DISPLAY_ROTATION=1
(phys_x = 127-ly, phys_y = lx); dispatch on display_type.
- variants/wio-tracker-l1-eink/platformio.ini: add
[env:WioTrackerL1Eink_companion_dual_dev] with ENABLE_SCREENSHOT.
- variants/wio-tracker-l1/platformio.ini: unchanged (OLED env already exists).
Builds verified: WioTrackerL1Eink_companion_dual_dev SUCCESS,
WioTrackerL1Eink_companion_radio_ble SUCCESS (unaffected).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
The previous fix set joystick_rotation=0 before reading from file, but
the subsequent rd() call overwrote it with whatever was stored (e.g. 2
from a prior e-ink firmware). Move the hardware-enforce block to after
rd() so stale values in flash are always corrected on OLED builds
(FEAT_JOYSTICK_ROTATION_SETTING=0). Remove the now-redundant pre-read
block.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- Adds the possibility to capture the device screen and save it as a PNG
image
- Wrap the code behind ENABLE_SCREENSHOT build flag, as per instructions
in README
Add per-channel favourite marking and a Settings filter (all/fav) for
the channel list, symmetric with the existing DM and Room filters.
NodePrefs:
- ch_fav_bitmask (uint64_t): bit i = channel i is marked favourite
- ch_fav_only (uint8_t): 0=show all channels, 1=favourites only
- SCHEMA_SENTINEL bumped to 0xC0DE0005
DataStore: save/load both new fields before the sentinel.
SettingsScreen: new CH_FILTER item ('Channels: all/fav') in the
Contacts section, positioned between DM_FILTER and ROOM_FILTER.
QuickMsgScreen:
- buildChannelList() skips non-favourite channels when ch_fav_only=1
- Channel context menu gains a 4th option 'Fav'/'Unfav' that toggles
ch_fav_bitmask for the selected channel and rebuilds the list
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
UITask: when a key is pressed while the buzzer is playing, defer the
next screen refresh by 300 ms instead of triggering it immediately
(via _next_refresh = 100). The blocking e-ink endFrame() was extending
the first note by the full refresh duration (~150-200 ms). Subsequent
notes were unaffected because _next_refresh was already future-dated
after the first render.
DataStore: for builds where JOYSTICK_ROTATION is not defined and
FEAT_JOYSTICK_ROTATION_SETTING is 0 (OLED), always reset
joystick_rotation to 0 on prefs load. Without this, stale e-ink prefs
(which allow changing joystick rotation in Settings) could silently
leave a non-zero value that reversed all joystick directions on OLED.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
In GxEPDDisplay::print(), the 0xDB fallback block was drawn at
cy - 8*scale, which assumed the Lemon baseline convention
(cy = original_y + 8*scale). For the default GFX font fontAscender
returns 0, so cy = original_y (top of cell) — the block landed
16 px above the character on e-ink (scale=2).
Fix: draw at cy (top of cell) for the non-Lemon path.
Also remove the unused forceNextRefreshFull() virtual from
DisplayDriver — it was added based on a wrong hypothesis (partial
refresh ghosting) and was never wired into endFrame().
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add an optional dot/intersection scale grid to the trail map view:
- renderGrid() draws labelled grid lines anchored to display edges
- Grid step auto-selected for ~3 intervals in the shorter dimension
- MIN_GRID_PX=22 prevents density on small/OLED screens; clamp ensures
minimum 2 intervals on large trails
- Intersections inside the label bbox and north-arrow bbox are suppressed
- Toggle via Hold-Enter action menu (Grid: ON/OFF item in ActionId enum)
- Map title shows 'TRAIL MAP+' when grid is active
- README updated to mention grid toggle
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Previous fix only evicted SHUTDOWN when cur_len == PAGE_ORDER_LEN (full).
If the array was not yet full but had SHUTDOWN + 2 missing pages (TOOLS and
QUICK_MSG), TOOLS would fill the last slot but QUICK_MSG would be left out.
Remove the cur_len guard: evict SHUTDOWN whenever any required page is
missing, regardless of array fullness. This frees one slot before the
append loop so all missing required pages can be added in a single pass.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Previous fix appended missing pages only when there was room (cur_len <
PAGE_ORDER_LEN). On e-ink builds with GPS+SENSORS the default order fills
all 11 slots; old saves that included SHUTDOWN instead of TOOLS/QUICK_MSG
had no room to append the missing entries.
Now, if the array is full and a required page is absent, SHUTDOWN is evicted
first (it is appended at runtime by buildVisibleOrder's fallback and does not
need to be in the explicit list). This frees a slot for the missing page.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
ensurePageOrderInit returned early after inserting FAVOURITES without
checking whether TOOLS/QUICK_MSG were present. Old page_order saves that
predated those pages had CLOCK+FAVOURITES but no Messages entry, so
movePageInOrder always found cur==-1 and silently did nothing.
Now recount valid entries after any insertion, then walk the full list of
required page bits and append any that are absent (if room exists).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Four findings from a code review pass on the Trail feature:
- showAlert overlay was gated to `curr == home`, so feedback like
"Tracking started", "Trail saved", "GPX N B (USB)" never rendered on
the Trail screen (or QuickMsg / Settings / Auto-Advert, for that
matter). Drop the gate — the overlay shows on whichever screen the
caller invoked from.
- TrailStore::writeTo only verified the first write; subsequent point
writes could partially fail (full filesystem, mid-write power loss)
and the method would still return true. Check every write return
value so handleSave's "Trail saved" only fires on actual success.
- gpxPoint: clamp snprintf's intended-length return against the buffer
size and skip the point if gmtime returns null. Avoids any chance of
out.write reading past buf[120].
- TrailScreen::_act_map sized exactly to today's 8 actions — bump to 12
so adding another popup item later doesn't cause an OOB write into
the surrounding members.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Adding the public DataStore::openWrite(const char*) member shadowed
the file-static openWrite(FILESYSTEM*, const char*) helper inside
DataStore.cpp's method bodies, so every internal call broke ("no
matching function" with two args). Qualify each internal call with
::openWrite so name lookup picks the static helper. The new public
member's own implementation already does that.
Trail.h's gpxPoint template called gmtime unqualified; ADL couldn't
find it from the template definition because no argument was
template-dependent. Include <time.h> and call ::gmtime — both passes
the dependency rule and avoids the -fpermissive-only acceptance.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Adds an "Export saved" item in the action popup (shown when /trail
exists). Streams GPX directly from the saved file to USB Serial,
skipping the RAM ring entirely — useful for dumping an old recording
after reboot when the live ring is empty (or busy with another
recording you don't want to overwrite via Load).
Refactors exportGpx into three helpers (gpxHeader, gpxPoint, gpxFooter)
shared by the RAM and file paths so the markup stays consistent. The
file path validates the same TRAL magic + version it accepts on Load.
handleExport and the new handleExportSaved both route through
showExportAlert so the "GPX N B (USB)" / "GPX N B - disc. app" hint
keeps reflecting the BLE-app-collision state described last time.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Blocking the export when BLE isn't connected also blocked the no-app
case (user attached only a terminal). Dump unconditionally and let the
confirm alert tell the user what just happened:
- BLE connected → "GPX N B (USB)" — USB receive is parked, no collision
- BLE absent → "GPX N B - disc. app" — reminder that the same USB
pipe the app would use just carried raw XML, so
reconnect/restart the app if you had one running
User can also reach the "no app, terminal-only" workflow naturally.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
The Wio L1 DualSerialInterface multiplexes BLE + USB on the same frame
protocol: when BLE is connected, the USB receive path is ignored, so we
can safely push raw GPX bytes to USB without confusing the companion
app. When BLE is *not* connected the app is talking over USB itself —
the dump would land mid-frame and the app would parse garbage.
Block the export when hasConnection() (BLE link to the app) is false
and show "Connect BLE or disconnect app". When it's true the dump runs
and the confirm alert reads "GPX N B over USB" so the user knows which
pipe to read from.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Single-slot persistence as agreed. Action popup grows three entries
(conditional on what makes sense for the current state):
- "Save trail" — writes the current RAM ring to /trail in LittleFS.
- "Load trail" — only shown when /trail exists; replaces the live ring
with the snapshot (any active session ends first).
- "Export GPX" — dumps the trail as a minimal GPX 1.1 document over
Serial so the user can capture it from a USB host.
Plumbing:
- TrailStore gains writeTo / readFrom (template on the file handle, so
the platform-specific File flavour stays out of Trail.h) plus
exportGpx(Stream&) for the GPX serializer. Header carries magic
"TRAL", a version byte, point count, and the accumulated active time
so elapsed survives the round trip.
- DataStore::openWrite is exposed publicly so callers outside DataStore
don't have to duplicate the platform open-mode dance.
- MyMesh gains a public getDataStore() accessor.
After Load, _pending_seg_break is set so any subsequent Start opens a
new segment instead of joining the loaded last point.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
