EthernetServer::available() returns any socket with data, including the
already-connected client's socket. The companion path then called stop()
on what it thought was a duplicate client, closing the shared socket and
disconnecting the companion after the first packet.
Switch both SerialEthernetInterface and EthernetCLI to server.accept(),
which only returns newly-accepted sockets. Removes the IP/port duplicate
detection in the companion path (no longer reachable) and the same-socket
early-return in the CLI path.
Reported by mcode6726 on PR #1983.
Adds ð/Ð (eth), þ/Þ (thorn) for Icelandic, and ţ/Ţ (t with cedilla)
for legacy-encoded Romanian text.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Adds háček and other Czech/Slovak characters (č š ž ř ě ů ď ť ň ľ ĺ ŕ)
to the UTF-8 transliteration table so they display as ASCII letters
instead of █ blocks.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Names printed via drawTextEllipsized (contacts, senders) bypassed
translateUTF8ToBlocks, causing raw UTF-8 bytes to render as garbage
on the Adafruit font. Now transliteration happens inside the method.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Replaces the block-character fallback with proper transliteration for
Polish (ą→a, ć→c, ę→e, ł→l, ń→n, ó→o, ś→s, ź→z, ż→z), German (ä ö ü ß),
and common French/Spanish/Portuguese accents. Unknown codepoints fall back
to '?' instead of █.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
tone() dynamically computes seq_refresh so the DMA repeats 50% duty for
~13-30ms per note before re-reading its buffer — volume cannot take effect
until that delay passes, producing a staircase artifact.
Replace tone()/NonBlockingRtttl with a custom RTTTL parser that drives
NRF_PWM2 directly using REFRESH=0. DMA now re-reads _duty_buf every
PWM period so:
- Duty is set before SEQSTART fires → no initial full-volume burst
- applyVolume() writes to _duty_buf and takes effect within one period (<2.3ms at A4)
- setVolume() during playback adjusts loudness immediately and smoothly
Non-nRF52 platforms continue to use NonBlockingRtttl + analogWrite.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add second ringtone slot (ringtone2_*) to NodePrefs and DataStore.
Add per-channel and per-DM melody assignment (built-in / melody 1 / 2)
stored in NodePrefs bitmasks and DmMelodyEntry table.
Settings screen exposes DM/CH sound items; RingtoneEditorScreen supports
switching between slots. notify() uses buildMelodyFromPrefs() to select
the correct RTTTL string per contact.
Remove broken nRF52 volume control from buzzer.cpp: tone() uses
NRF_PWM2 with DECODER.MODE=Auto so TASKS_NEXTSTEP has no effect and
duty cannot be changed before the first DMA read without patching the
Arduino core. applyVolume() is now a no-op on nRF52.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- RingtoneEditorScreen: 32-note step sequencer accessible via new Tools page on home screen. U/D=pitch, ENTER=octave cycle, L/R=cursor, MENU=options (play, duration, BPM, insert/delete, save). Notes stored packed in NodePrefs and persisted via DataStore.
- ToolsScreen: new "Tools" home page entry launching the editor
- Buzzer volume: 0-4 bar control in Settings > Sound, persisted to prefs
- Buzzer notifications: fixed notify() firing inside wrong serial-guard branch and before addChannelMsg set the channel index
- Unread counter: fixed newest-first index direction; watermark formula now correct
- OLED brightness: wider range via pre-charge register 0xD9 combined with contrast
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- NodePrefs: add buzzer_volume field (0=min..4=max, default 4)
- DataStore: persist buzzer_volume at end of prefs file (backward-compat)
- buzzer: setVolume()/getVolume(); applyVolume() sets PWM duty cycle via
analogWrite() after each rtttl::play() call to control output amplitude
- Settings UI: new BzrVol bar item in Sound section (left/right to adjust)
- UITask: apply saved volume on startup alongside brightness
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- MyMesh: notify() now always fires for channel/contact messages regardless
of serial connection; called after addChannelMsg so channel index is set
- ChannelHist: fix unread watermark direction (histEntry is newest-first,
index 0=newest); counter now decrements correctly as user reads messages
- ChannelHist: reset unread to 0 after sending (user is active in channel)
- SH1106Display: add pre-charge register (0xD9) to setBrightness for wider
dimming range; re-apply contrast+precharge in turnOn(); tune curve
- UITask: remove MsgPreviewScreen dead code (~180 lines, never shown)
- UITask: fix strcpy→snprintf in showAlert()
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- SensorManager::getAvailableLPPTypes() reports which LPP types will be
present based on initialized sensor flags (temp, humidity, pressure, etc.)
- Sensors page renders one row per available type; shows "--" for any sensor
that hasn't produced a reading yet instead of hiding the row entirely
- LPPReader: add readLuminosity, readPercentage, readConcentration, readDistance
- All known LPP types now have proper names and units in the sensor display
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
buzzer.play() was returning early when _is_quiet=true, so channels with
explicit notification=ON were silent even though the logic correctly set
play=true. playForced() bypasses the quiet check for these overrides.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add a new command `region bulk` for defining region hierarchies in a single line. This command allows users to create multiple regions in a single message. Updated the documentation to include usage examples and detailed parameter descriptions.
This slipped through in PR #2327 and I noticed because the TechoBoard.h
for my variant doesn't include the Wire header, so the source file
in question does not coincidentally obtain a copy.
The `::init` method in the Adafruit ST7789 library is responsible to
initialize the device. This includes performing a reset, which can be
found in the Adafruit source for `Adafruit_SPITFT`.
Before this change, MeshCore performed its own ST7789 display reset
sequence, which consisted of three steps.
* Pull reset low
* Wait 10ms
* Pull reset high
Importantly, there was no fixed delay after pulling reset high. The
ST7789 driver requires a delay (T<sub>RT</sub>) of 5ms in Sleep In Mode
and 120ms in Sleep Out Mode before it will properly receive commands.
When `Adafruit_SPITFT` resets the device after MeshCore has already
reset it, the mandatory time may not have elapsed, leading to strange
behavior. In the author's case, this issue caused the initial
`fillScreen` to fail, such that the display showed an uninitialized
framebuffer.
This removes the MeshCore delay, leaving the responsibility of reset to
`Adafruit_SPITFT`, where they have the correct delays in place with
extra safety margin. The change was briefly tested by Josiah VanderZee
and Ben Zignego on a custom hardware build using an nRF52840 Dongle and
an Adafruit 4311 TFT display. The user button seemed to behave
strangely, but the display looked correct.
USE_LR1110 was missing from the preprocessor guard in CommonCLI.cpp,
causing both get and set to fail silently on T1000-E:
- get radio.rxgain returned the full radio config string (fell through
to the memcmp("radio", 5) branch)
- set radio.rxgain returned "unknown config" (no branch matched)
Fix: add -D USE_LR1110 to variants/t1000-e/platformio.ini and include
USE_LR1110 in the #if guard on both get and set branches.
CustomLR1110Wrapper already implements setRxBoostedGainMode() and
getRxBoostedGainMode() via the RadioLibWrapper virtual interface,
so no radio-layer changes are required.
Tested on T1000-E: get/set/persist all confirmed working.
Scott Powell
Ryan Gregg
JakubandClaude Sonnet 4.6
agessaman
Quency-D
Stephen Waits
taco
Quency-DandGitHub
Josiah VanderZee
Liam CottleandGitHub
Wessel Nieboer
Kenneth Privitt
Nick Le Mouton
jirogit
Kyle
