Same reasoning as the Cardputer ADV / T-Echo Lite KeyShield note --
new board support that hasn't had much real-world use yet.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Names the upcoming release and marks the Cardputer ADV / T-Echo Lite
KeyShield board support as experimental, since it's new enough not to
have had much real-world use yet.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The pre-v1.13 "GPS Interval" setting (hidden from Settings ever since,
but its byte kept "for backwards compatibility") used a different option
set than today's duty-cycle presets -- its old 30s choice isn't one of
them. A device that had it set to 30 would load that value straight into
the new duty-cycle scheduler while "GPS pwr" in Settings showed OFF
(gpsDutyIndex() found no matching preset), silently cycling GPS on a
setting nobody could see or change. Unrecognised values now reset to OFF
on load, same as the existing out-of-range clamp this replaces.
Also refreshes MyMesh.h's FIRMWARE_VERSION/FIRMWARE_BUILD_DATE fallback
(only ever used by a `pio run` that bypasses build.sh entirely) -- it
was still "v1.17-solo.0" from 12 tags ago.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Restructures already-shipped v1.24 content out of Unreleased into its
own version section, adds the missing v1.22 heading and a v1.21
separator, documents the M5Stack Cardputer ADV / LilyGO T-Echo Lite
KeyShield board support, and folds in the locked-screen Messages fix,
the GPS duty-cycle races, and the OFF-casing cleanup.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Every genuine on/off toggle already agreed on ON/OFF, but the disabled
point of several value pickers didn't: Settings' LowBat/GPS pwr/e-ink
full-refresh options and the auto-advert interval showed lowercase
"off", GPIO's mode row showed "Off" right above its own State row's
"OFF", and the GPS-averaging/trail-autopause pickers showed "Off" where
the alarm-repeat picker already said "OFF". All display-only label
arrays, no behaviour change.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Two races between the new GPS duty-cycle scheduler and code that changes
GPS state independently of it:
- gpsDutyCycleLoop() capped every "GPS on" phase at a fixed 60s and would
stop_gps() as soon as a fix went valid, with no awareness of an
in-flight "!gps fix" bot request -- so a fix's own up-to-300s acquire
window (and its 10s averaging phase) could get cut short by the
scheduler shutting GPS off mid-request. MyMesh::isGpsFixPending() now
feeds into UITask's existing "is anything live using GPS right now"
hold, alongside trail/live-share/locator/nearby.
- setSettingValue("gps", ...) (Settings toggle, bot !gps on/off, CLI)
starts/stops GPS directly without resetting the scheduler's own phase
timer, so a manual toggle could land on a stale, already-expired
deadline left over from before -- immediately re-stopping GPS a tick
after turning it on. The phase timer now resets on every external
change, so the next duty-cycle tick re-arms fresh.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
formatDashVal(), the locked-screen counterpart to the unlocked clock's
dashboard rendering, never learned about DASH_MSGS and fell through to
an empty string for it, so Messages was the one CLOCK FIELDS choice
that showed nothing at all once the screen locked.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
SPI pins that are set to -1 cause OOB reads on NRF52. The unused Serial2 pin definitions were removed to avoid potential issues with the Uart framework.
Setting SPI pins to values that are OOB of the g_ADigitalPinMap[] array causes OOB reads. This variant.h has pin 0 as 0xFF which passes through as NRFX_SPIM_PIN_NOT_USED.
Brings in upstream companion-v1.17.0 (CAD, MCU temp telemetry, misc
fixes) alongside our RX duty-cycle power-save; see merge-upstream-v1.17
history for the full conflict-resolution rationale.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Adopts hardware Channel Activity Detection (wired into
RadioLibWrapper::isChannelActive() alongside our RSSI-threshold check
and RX duty-cycle power-save), MCU temperature telemetry, LR2021
standby workaround, DISPLAY_SCALE/FLIP overrides, NRF52Board
shutdownPeripherals() refactor, and misc upstream fixes.
Declines upstream's ConfigSerializer-based NodePrefs rewrite,
MultiSerialInterface/interface_manager, and UIColor palette system —
each would have broken large parts of the Solo-specific feature set
(NodePrefs fields, per-variant single serial_interface, enum-based
DisplayDriver::Color). Flagged as candidate follow-up migrations, not
permanent no's.
Also fixes several pre-existing bugs surfaced while chasing silent
merge breaks (stale newMsg() override signature in ui-tiny/ui-orig,
dead UIEventType::newContactMessage case, missing ContactsIterator
init), bumps FIRMWARE_VERSION/MESHCORE_VERSION to 1.17, and fixes a
missing <cstdlib> include that broke the native ConfigSerializer unit
tests.
Verified via 13+ pio run builds across ESP32/nRF52, all 3 companion UI
variants, and 7 display drivers, plus the full native unit test suite
(33/33 passing).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Introduced consistent preferences for external LoRa FEM RX and TX gain settings in NodePrefs. Updated companion MyMesh to apply these settings during initialization and transmission. Added unit tests to verify the round-trip serialization of these new preferences.
MarekZegare4andClaude Sonnet 5
taco
ripplebizandGitHub
JakubandClaude Sonnet 5
Huw DuddyandGitHub
Rastislav Vysoky
agessaman
Liam CottleandGitHub
Wessel Nieboer
Dan Theisen
Florent
entr0p1