BLE takes priority when connected; USB is always ready as fallback.
Both state machines run continuously — no BLE disconnect on USB connect.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- Use inverted PWM polarity (0x8000) with PCT {2,5,12,25,50} giving
~6-8 dB perceptual steps (-24/-16/-9/-3/0 dB) vs the original
uneven steps where levels 4 and 5 were only 1 dB apart
- Guard against cmp=0 truncation in both _nrfStartPwm and applyVolume:
at level 1 with high notes (freq > ~2.5 kHz) integer math gives
cmp=0 which with inverted polarity means 100% HIGH → complete silence
- Change volume preview note from C5 (523 Hz) to C6 (1047 Hz) to better
match the piezo resonant frequency range and actual notification sounds
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Adds ð/Ð (eth), þ/Þ (thorn) for Icelandic, and ţ/Ţ (t with cedilla)
for legacy-encoded Romanian text.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Adds háček and other Czech/Slovak characters (č š ž ř ě ů ď ť ň ľ ĺ ŕ)
to the UTF-8 transliteration table so they display as ASCII letters
instead of █ blocks.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Names printed via drawTextEllipsized (contacts, senders) bypassed
translateUTF8ToBlocks, causing raw UTF-8 bytes to render as garbage
on the Adafruit font. Now transliteration happens inside the method.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Replaces the block-character fallback with proper transliteration for
Polish (ą→a, ć→c, ę→e, ł→l, ń→n, ó→o, ś→s, ź→z, ż→z), German (ä ö ü ß),
and common French/Spanish/Portuguese accents. Unknown codepoints fall back
to '?' instead of █.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
tone() dynamically computes seq_refresh so the DMA repeats 50% duty for
~13-30ms per note before re-reading its buffer — volume cannot take effect
until that delay passes, producing a staircase artifact.
Replace tone()/NonBlockingRtttl with a custom RTTTL parser that drives
NRF_PWM2 directly using REFRESH=0. DMA now re-reads _duty_buf every
PWM period so:
- Duty is set before SEQSTART fires → no initial full-volume burst
- applyVolume() writes to _duty_buf and takes effect within one period (<2.3ms at A4)
- setVolume() during playback adjusts loudness immediately and smoothly
Non-nRF52 platforms continue to use NonBlockingRtttl + analogWrite.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add second ringtone slot (ringtone2_*) to NodePrefs and DataStore.
Add per-channel and per-DM melody assignment (built-in / melody 1 / 2)
stored in NodePrefs bitmasks and DmMelodyEntry table.
Settings screen exposes DM/CH sound items; RingtoneEditorScreen supports
switching between slots. notify() uses buildMelodyFromPrefs() to select
the correct RTTTL string per contact.
Remove broken nRF52 volume control from buzzer.cpp: tone() uses
NRF_PWM2 with DECODER.MODE=Auto so TASKS_NEXTSTEP has no effect and
duty cannot be changed before the first DMA read without patching the
Arduino core. applyVolume() is now a no-op on nRF52.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- RingtoneEditorScreen: 32-note step sequencer accessible via new Tools page on home screen. U/D=pitch, ENTER=octave cycle, L/R=cursor, MENU=options (play, duration, BPM, insert/delete, save). Notes stored packed in NodePrefs and persisted via DataStore.
- ToolsScreen: new "Tools" home page entry launching the editor
- Buzzer volume: 0-4 bar control in Settings > Sound, persisted to prefs
- Buzzer notifications: fixed notify() firing inside wrong serial-guard branch and before addChannelMsg set the channel index
- Unread counter: fixed newest-first index direction; watermark formula now correct
- OLED brightness: wider range via pre-charge register 0xD9 combined with contrast
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- NodePrefs: add buzzer_volume field (0=min..4=max, default 4)
- DataStore: persist buzzer_volume at end of prefs file (backward-compat)
- buzzer: setVolume()/getVolume(); applyVolume() sets PWM duty cycle via
analogWrite() after each rtttl::play() call to control output amplitude
- Settings UI: new BzrVol bar item in Sound section (left/right to adjust)
- UITask: apply saved volume on startup alongside brightness
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- MyMesh: notify() now always fires for channel/contact messages regardless
of serial connection; called after addChannelMsg so channel index is set
- ChannelHist: fix unread watermark direction (histEntry is newest-first,
index 0=newest); counter now decrements correctly as user reads messages
- ChannelHist: reset unread to 0 after sending (user is active in channel)
- SH1106Display: add pre-charge register (0xD9) to setBrightness for wider
dimming range; re-apply contrast+precharge in turnOn(); tune curve
- UITask: remove MsgPreviewScreen dead code (~180 lines, never shown)
- UITask: fix strcpy→snprintf in showAlert()
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- SensorManager::getAvailableLPPTypes() reports which LPP types will be
present based on initialized sensor flags (temp, humidity, pressure, etc.)
- Sensors page renders one row per available type; shows "--" for any sensor
that hasn't produced a reading yet instead of hiding the row entirely
- LPPReader: add readLuminosity, readPercentage, readConcentration, readDistance
- All known LPP types now have proper names and units in the sensor display
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
buzzer.play() was returning early when _is_quiet=true, so channels with
explicit notification=ON were silent even though the logic correctly set
play=true. playForced() bypasses the quiet check for these overrides.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* room server: added RegionMap, and new CommonCLI wiring, default_scope handling
* sensor: only minimal RegionMap wiring. Still needs work to handle default-scope
ESP-NOW radios (ie, Generic_ESPNOW_* variants) do not compile due to
missing methods
Changes in January 2026 (019bbf74) to add additional stats (receive errors)
to CMD_GET_STATS was not implemented in the ESPNOWRadio() class
Changes in March 2026 (9a95e25e) to add setRxBoostedGainMode to all devices
rather than just SX1262/SX1268 were not applied to the ESPNowRadio() driver
Specifically, this change adds the following to ESPNOWRadio()
* getPacketsRecvErrors() - always returns 0
* getRxBoostedGainMode() - always returns false
* setRxBoostedGainMode() - does nothing
Allow for platformio.ini files to override the default values for the
following INA3221 related macros:
TELEM_INA3221_ADDRESS
TELEM_INA3221_SHUNT_VALUE
TELEM_INA3221_NUM_CHANNELS
Signed-off-by: Paul Moore <paul@paul-moore.com>
