Follow-up to the UI casing unification -- the docs quoting these same
option values (Settings' Auto-lock/Buzzer/Full refresh/Low battery/GPS
pwr/Resend rows, Tools' Auto-pause/Mark avg/Auto-save/Auto-Advert/
Heartbeat/GPIO rows, and the clock alarm's Repeat cycle) still showed
the old lowercase/Title-case spellings the screens themselves no
longer use.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
README's Supported Devices table and Flashing section gain the
Cardputer ADV and T-Echo Lite + KeyShield rows/headings (both marked
experimental, matching release-notes.md and the Heltec V3/V4 entries).
external_keyboard.md gets a new section for their built-in TCA8418
keypads -- a separate mechanism from CardKB, not documented anywhere
before. settings_screen.md's GPS pwr row now lists !gps fix among the
things that hold GPS continuously on, matching the actual code.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The prior entries carried full root-cause narrative for each change,
matching this file's older sections -- too dense for what's meant to
be a quick skim. Cut down to what changed and where.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Same reasoning as the Cardputer ADV / T-Echo Lite KeyShield note --
new board support that hasn't had much real-world use yet.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Names the upcoming release and marks the Cardputer ADV / T-Echo Lite
KeyShield board support as experimental, since it's new enough not to
have had much real-world use yet.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The pre-v1.13 "GPS Interval" setting (hidden from Settings ever since,
but its byte kept "for backwards compatibility") used a different option
set than today's duty-cycle presets -- its old 30s choice isn't one of
them. A device that had it set to 30 would load that value straight into
the new duty-cycle scheduler while "GPS pwr" in Settings showed OFF
(gpsDutyIndex() found no matching preset), silently cycling GPS on a
setting nobody could see or change. Unrecognised values now reset to OFF
on load, same as the existing out-of-range clamp this replaces.
Also refreshes MyMesh.h's FIRMWARE_VERSION/FIRMWARE_BUILD_DATE fallback
(only ever used by a `pio run` that bypasses build.sh entirely) -- it
was still "v1.17-solo.0" from 12 tags ago.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Restructures already-shipped v1.24 content out of Unreleased into its
own version section, adds the missing v1.22 heading and a v1.21
separator, documents the M5Stack Cardputer ADV / LilyGO T-Echo Lite
KeyShield board support, and folds in the locked-screen Messages fix,
the GPS duty-cycle races, and the OFF-casing cleanup.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Every genuine on/off toggle already agreed on ON/OFF, but the disabled
point of several value pickers didn't: Settings' LowBat/GPS pwr/e-ink
full-refresh options and the auto-advert interval showed lowercase
"off", GPIO's mode row showed "Off" right above its own State row's
"OFF", and the GPS-averaging/trail-autopause pickers showed "Off" where
the alarm-repeat picker already said "OFF". All display-only label
arrays, no behaviour change.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Two races between the new GPS duty-cycle scheduler and code that changes
GPS state independently of it:
- gpsDutyCycleLoop() capped every "GPS on" phase at a fixed 60s and would
stop_gps() as soon as a fix went valid, with no awareness of an
in-flight "!gps fix" bot request -- so a fix's own up-to-300s acquire
window (and its 10s averaging phase) could get cut short by the
scheduler shutting GPS off mid-request. MyMesh::isGpsFixPending() now
feeds into UITask's existing "is anything live using GPS right now"
hold, alongside trail/live-share/locator/nearby.
- setSettingValue("gps", ...) (Settings toggle, bot !gps on/off, CLI)
starts/stops GPS directly without resetting the scheduler's own phase
timer, so a manual toggle could land on a stale, already-expired
deadline left over from before -- immediately re-stopping GPS a tick
after turning it on. The phase timer now resets on every external
change, so the next duty-cycle tick re-arms fresh.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
formatDashVal(), the locked-screen counterpart to the unlocked clock's
dashboard rendering, never learned about DASH_MSGS and fell through to
an empty string for it, so Messages was the one CLOCK FIELDS choice
that showed nothing at all once the screen locked.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Brings in upstream companion-v1.17.0 (CAD, MCU temp telemetry, misc
fixes) alongside our RX duty-cycle power-save; see merge-upstream-v1.17
history for the full conflict-resolution rationale.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Adopts hardware Channel Activity Detection (wired into
RadioLibWrapper::isChannelActive() alongside our RSSI-threshold check
and RX duty-cycle power-save), MCU temperature telemetry, LR2021
standby workaround, DISPLAY_SCALE/FLIP overrides, NRF52Board
shutdownPeripherals() refactor, and misc upstream fixes.
Declines upstream's ConfigSerializer-based NodePrefs rewrite,
MultiSerialInterface/interface_manager, and UIColor palette system —
each would have broken large parts of the Solo-specific feature set
(NodePrefs fields, per-variant single serial_interface, enum-based
DisplayDriver::Color). Flagged as candidate follow-up migrations, not
permanent no's.
Also fixes several pre-existing bugs surfaced while chasing silent
merge breaks (stale newMsg() override signature in ui-tiny/ui-orig,
dead UIEventType::newContactMessage case, missing ContactsIterator
init), bumps FIRMWARE_VERSION/MESHCORE_VERSION to 1.17, and fixes a
missing <cstdlib> include that broke the native ConfigSerializer unit
tests.
Verified via 13+ pio run builds across ESP32/nRF52, all 3 companion UI
variants, and 7 display drivers, plus the full native unit test suite
(33/33 passing).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
New M5Stack Cardputer ADV variant (ESP32-S3, ST7789 TFT, built-in TCA8418
QWERTY keyboard, PI4IOE5V6408 LoRa-cap IO-expander autodetect), and a
KeyShield accessory variant for the existing LilyGO T-Echo Lite (external
TCA8418 T9 keypad + AW21009 backlight driver). Both keyboards share one
ENV_USE_TCA8418 polling block in UITask.cpp::loop(), coexisting with the
unrelated CardKB support (different chip/address/flag).
Fixes carried in from the contributed T-Echo Lite code: swapped GPS RX/TX
pins, TX-LED hooks, TCXO voltage, missing GxEPD2_122_T61 panel include.
Fixed during integration: I2C bus was probed for an RTC before Wire.begin()
configured its pins on Cardputer ADV (silent RTC autodetect failure).
Added dedicated *_solo_dual release envs for both boards (auto-picked up by
the solo-firmware release workflow). Gave the T-Echo Lite KeyShield solo
build -Os/-Ofast-unflag like every other nRF52 solo build (was missing,
cut flash usage from 90.7% to 61.4%).
Ported the shared misc-fixed 6x9 font (full Latin/Greek/Cyrillic, opt-in via
OLED_MISC_FIXED_FONT) to ST7789Display for the Cardputer's on-screen
keyboard. ST7789Spi isn't Adafruit_GFX-based like the other single-font
drivers, and this panel's logical->physical scale is non-integer, so glyphs
are re-packed to XBM and blitted through the existing drawXbm(), which
already does correct fractional-scale boundary math, rather than
duplicating that logic.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Settings screen doc gets the new "GPS pwr" row and a watchdog note on
"Pwr save"; Diagnostics doc gets the new "RXPS wd s/h" row and updates
what "Reset counters" actually clears; release-notes.md gets Unreleased
entries for all three additions from the prior commit.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Three power-saving additions, prompted by comparing this fork's existing
RX duty-cycle support against IoTThinks/EasySkyMesh:
- RX duty-cycle watchdog: the SX126x's hardware RX<->sleep sequencer runs
with no MCU polling, so a desync (a known failure mode) previously had
nothing watching for it. A new watchdog samples the BUSY pin every tick;
no transition for too long triggers a soft re-arm, then a full chip
reset (with cached radio params reapplied, since std_init() resets to
compiled firmware defaults) if that doesn't clear it. Soft/hard recovery
counts surface on Tools > Diagnostics > Live as "RXPS wd s/h".
- Noise-floor recalibration during power-save: sampling was previously
skipped entirely while duty-cycling, freezing int.thresh interference
detection at whatever the floor was when power-save turned on. Now
borrows a brief continuous-RX window once a minute to take a fresh
reading before re-arming duty-cycle.
- GPS duty-cycling (Settings > System > "GPS pwr"): cycles GPS off between
fixes instead of running it continuously. Each wake waits for a fix
(capped at 60s) before sleeping again for the configured interval.
Repurposes the long-dead NodePrefs::gps_interval byte rather than adding
a new persisted field. A "is anything live using GPS right now" hold in
UITask keeps GPS continuously on whenever trail recording, live-share,
an armed Locator, or the Compass/Nearby-navigate view actually need a
live fix, so none of those features degrade. Locator crossing-state is
reset on each wake so a still-settling first fix can't read as a false
geofence crossing.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
README had drifted from the firmware in several places:
- Supported Devices listed only the three nRF52 boards; Heltec V3/V4 were
missing entirely, as was any mention that ESP32-S3 flashes differently.
Flashing is now split per MCU, with the merged-vs-app-only .bin trap
spelled out — that one costs an afternoon to diagnose from a dark screen.
- It advertised a Lemon/Default font switch that was retired in v1.23; there
is one unified misc-fixed 6x9 font now and no font setting at all.
- tools/README claimed ENABLE_SCREENSHOT had to be added by hand, directly
contradicting README's "no special build flags required". The envs have
carried the flag for a while; rewrote the file to cover all four tools.
- "S key for screenshot" described screenshot.py's menu, not the device —
screenshots are driven entirely from the host via CMD_GET_SCREENSHOT.
Structurally, general notes (factory reset on migration, BLE-over-USB
priority) sat at the tail of the ESP32 subsection and read as ESP32-specific;
they're now placed where they apply. Heltec wiring moved out of Supported
Devices into its own section so the device table stays scannable, and the
Solo Tools heading is no longer a link (it was generating a garbage anchor).
New docs/solo_features/external_keyboard.md covers CardKB and the wired
joystick: shortcut table, Full vs Compact, and the pin assignment. The pins
are marked as verified on real V4 hardware only — V3 inherits them from
Heltec's documented pin-compatibility and hasn't been checked on a board.
FEATURES.md (roadmap + code audit, developer-only) moves to
docs/development/roadmap.md; nothing referenced it by path.
Adds Building from source / Releasing / Repository layout, since the release
flow was only discoverable by reading the workflow.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The solo release job only attached *.uf2 and *.zip, which covered every solo
board back when they were all nRF52. The Heltec V3/V4 .bin images were built
and then silently dropped, so tagging a release produced nothing downloadable
for those two boards.
Releases now carry a single -merged.bin per ESP32 board (bootloader +
partition table + app at 0x0). build.sh also writes an app-only .bin, but
that one needs offset 0x10000 and a bootloader already on the chip, so it's
deleted before upload rather than shipped next to the merged image — flashing
it at 0x0 looks exactly like a bricked device.
Also adds -D ENABLE_SCREENSHOT to both Heltec solo envs. Every other solo env
already had it, so Solo Tools couldn't capture these two boards' displays and
the README's "no special build flags required" was untrue for them. Both envs
rebuilt clean (V3: RAM 58.8%, Flash 43.2%).
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
V3 and V4 are pin-compatible per Heltec's docs, and V3's own PIN_GPS_RX/TX/EN
defines are dead code here (ENV_INCLUDE_GPS is never set to 1 in this file),
so there's no reason to keep the blind-guess pins from before. Reuses the
exact CardKB (SDA 3/SCL 4) and joystick (UP 23/DOWN 6/LEFT 47/RIGHT 48/BACK 33)
assignment already confirmed working on real V4 hardware.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Port the Wio Tracker L1 solo firmware (full on-device UI, dual BLE/USB
companion transport) to Heltec V3 and V4 OLED boards. Neither board has
a joystick or CardKB on-board, so each new env wires up both as optional
peripherals with default pins from what the board leaves free, gated
behind the existing UI_HAS_JOYSTICK/ENV_PIN_SDA+SCL flags.
DUAL_SERIAL was nRF52-only; added an ESP32 helpers/esp32/DualSerialInterface.h
counterpart so the flag isn't silently ignored on these boards. On V4's
native USB CDC, isClientConnected() also honours (bool)Serial (real DTR),
same as the nRF52 version; V3 has no native CDC so it stays BLE-only there.
Screen (SDA 17/SCL 18) and CardKB (SDA 3/SCL 4) confirmed working on real
V4 hardware.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Board manifest for esp32-c6-devkitm-1 defaults build.flash_mode to qio,
which this module's flash chip does not support -- causes a boot
crash-loop (repeated USB-Serial-JTAG reconnects) on real hardware.
Override with board_build.flash_mode = dio in the common M5Stack_Unit_C6L
section so it applies to all envs (ble/usb/repeater/room_server).
CustomLR1110::startReceive() passed RADIOLIB_LR11X0_IRQ_PREAMBLE_DETECTED
(1<<4 = 16) as RadioLib's first argument, which is the RX *timeout*, not an
IRQ mask. At the LR11x0's 30.52us tick that armed the receiver for ~488us, so
it dropped out of RX before any packet could arrive and the node received
nothing at all -- while transmitting normally.
Symptoms on a SenseCAP T1000-E: tx_air_secs rising, rx_air_secs stuck at 0,
recv_errors 0, and the noise floor pinned at the -120 clamp because
getCurrentRSSI() never sampled a live receiver.
Pass RADIOLIB_LR11X0_RX_TIMEOUT_INF (continuous RX), which is what
LR11x0::startReceive() itself uses, keeping the PREAMBLE_DETECTED flag in the
reported IRQ flags as intended.
Introduced in ea5d7c8b ("LR1110: add PREAMBLE_DETECTED to reported irq flags").
Verified on two T1000-E units: with only the repeater fixed it began receiving
(last_rssi -29, SNR 17.0) while the unfixed companion stayed deaf; fixing both
brought up the link in each direction.
MarekZegare4andClaude Sonnet 5
JakubandClaude Sonnet 5
Scott Powell
Huw DuddyandGitHub
taco
Hacuchino-hash
liamcottle
Rastislav VysokyandGitHub
fdlamotteandGitHub
me
Mike Damon