The prefs schema-migration block runs on every SCHEMA_SENTINEL mismatch, and
the "turn Favourites on" step was ungated. Since each firmware release bumps
the sentinel, every update re-applied `home_pages_mask |= HP_FAVOURITES`,
clobbering a user who had hidden it. Gate it to the transition that added
Favourites (sentinel < 0xC0DE0002), matching the trail_units_idx migration.
The Map/Trail carousel page shipped with no visibility toggle: pageBit(MAP)
returned -1 so it was always visible with no Settings row. Add a proper "Map"
toggle (new HPB_MAP/HP_MAP bit, pageBit/bitToPage cases, HOME_MAP settings
row) plus a gated one-time migration (sentinel < 0xC0DE0018) that keeps it
visible for upgraders. Bump SCHEMA_SENTINEL to 0xC0DE0018; page_order[] stays
a literal 11 so the persisted layout is unchanged.
Also fix the fresh-install seed, which used a stale 0x01FF literal that left
Favourites hidden on new installs despite its "all pages visible" comment;
seed NodePrefs::HP_ALL so fresh installs match upgraders (Favourites + Map).
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Every drawList/AccordionList row opened with the same hand-written
display.drawSelectionRow(0, y-1, width-reserve, lineStep-1, sel) line —
14 copies of the same geometry and magic offsets. Add a drawRowSelection(d,
y, sel, reserve) helper in icons.h next to drawList and route the canonical
sites through it (Bot/LiveShare/Locator/Repeater/Settings/Tools/Nearby/
QuickMsg/Waypoints).
Rows that intentionally differ (full-width DashboardConfig/QuickMsg, the
keyboard/ringtone grids) keep their explicit drawSelectionRow() call — the
helper is opt-in rather than baked into drawList, so legitimate variants
aren't forced into one geometry. Framework doc updated to match.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
The "_dirty bool, then if (_dirty) the_mesh.savePrefs() on exit" pattern was
duplicated across 9 screens with subtle divergence: some cleared the flag
after saving, some left it set and relied on onShow() to reset. Replace all
12 exit sites with a single _task->savePrefsIfDirty(flag) helper that saves
once only if dirty and always clears the flag, so the "did we touch flash?"
answer lives in one place and the reset is consistent.
Edit sites still mark the flag manually (inherent to change tracking); only
the persist-on-exit boilerplate is centralised.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Replace the ad-hoc enter()/markClean() entry methods (which lived outside
the UIScreen interface and were invoked via casts from each gotoX) with a
virtual onShow() lifecycle hook called centrally by setCurrScreen().
This removes the "forgot to call enter() in a new navigator" footgun and
the unchecked cast smell: 12 navigators collapse to one-line
setCurrScreen(x) calls, and override enforces signature match. Two entries
that carry a parameter/variant keep an explicit typed call after
setCurrScreen(): RingtoneEditor::selectSlot(slot) and TrailScreen::showMapView().
Behaviour-preserving: only screens that previously had enter() get an
onShow() override; Splash/Home/QuickMsg/Diag keep no reset as before.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Squash merge of feat/location-beacon-alerts-autopause (v1.21).
Features:
- Live Location Sharing — broadcast position as movement-gated [LOC]
messages to a channel or contact; live shares show as map pins with
distance/bearing in Nearby Nodes and a status-bar indicator. [LOC] is
parsed in DMs, channel messages and room messages; DM shares name the
sender.
- Locator (geofence) — arm a geofence around a saved waypoint or a person
(live [LOC] or last-known position), alert on arrive/leave or near/far,
with an optional homing beeper (gated to arrive/both modes). Arm from
Tools > Locator, Nearby Nodes, or Waypoints; target picker lists
favourites first, clearable via a "None" entry. Active target is drawn
as a flag on the map.
- One active target shared across Locator / Navigate / Map via a single
resolver (resolvePersonPos / activeTargetPos) that prefers a live
[LOC] share over the last-advertised GPS fix.
- Follow live contacts — Navigate to a live-sharing contact follows them
as they move and adds an ETA line; quick-share your own position from
the Map.
- Map & status-bar upgrades — home mini-map gets a north marker, scale
tick, and a connected trail line (was disconnected dots); status line
shows tracked-node count, an arrow + distance to the active Locator/Nav
target (falling back to the nearest live-tracked contact); GPS fix icon
in the top status bar, shown only on GPS boards with GPS enabled.
- Trail auto-pause — recording freezes on stops (banking elapsed time,
breaking the map line across the idle gap) and resumes on movement
without ending the session.
- Streaming trail simplification — GPS points are simplified in-stream
via a fixed-corridor (Reumann-Witkam) pass tuned for fidelity: straight
runs collapse to their endpoints, curves stay bounded to the Min-dist
tolerance, so the 512-point buffer covers a far longer route than a
flat point budget would suggest.
- Collapsible Tools (Location / Comms / System sections, fold-in-place
like Settings) and page-indicator icons on the home carousel.
- Waypoint coordinate editor — add a waypoint by scroll-editing lat/lon
digit by digit.
Fixes:
- Critical: low-heap hang and contact loss on RAM-tight builds. Halved
message-history scrollback rings (recovering ~14 KB free heap) and
made contacts/channels/prefs persistence atomic (temp file + rename),
so an interrupted save can no longer corrupt or wipe the store.
- Serial.write() bounded so a stalled USB host can't hang the device.
- Nearby Nodes: live [LOC] senders respect the type filter, sort by
shared position, and the list refreshes so live shares bubble up.
- Map: live contacts are labelled before waypoints.
- GPS status icon hidden when GPS is off in Settings.
- Splash screen no longer truncates a pre-release tag's own dash (e.g.
v1.21-rc1) when stripping the build's commit-hash suffix.
- Null-guarded the Locator target picker; clamped loc-share channel
index on load.
Under the hood:
- -Os size optimisation on the e-ink and GAT562 30S solo envs.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
The manual Freq/SF/BW/CR editing was duplicated near-verbatim between
Settings › Radio and Tools › Repeater — same digit-by-digit Freq editor,
same SF/BW/CR step bounds, differing only in the target fields and the
apply call. Extract RadioParamsEditor (freq DigitEditor + static SF/BW/CR
steppers), with no dependency on UITask or the radio driver: the screen
passes the freq bounds in, the same way RadioPresetPicker stays decoupled.
Completes the preset-picker consolidation.
Behaviour preserved: a step at the range limit changes nothing and isn't
consumed (falls through), as before.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Settings › Radio and Tools › Repeater had near-identical preset-picker
logic (name/list-index lookup, save/delete, popup build, selection
handling) plus their own copy of the nearest-bandwidth search — only the
target fields (companion params vs. dedicated repeater profile) and the
apply call differed.
Extract the shared logic into RadioPresetPicker (a Target of field
pointers + a Result the screen acts on), with no dependency on UITask so
each screen keeps its own apply/dirty/keyboard/alert handling. Move the
nearest-bandwidth search to nearestBwIndex() in RadioPresets.h. Removes
~6 duplicated methods and 4 state fields from each screen.
Verified: WioTrackerL1_companion_solo_dual builds clean.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Settings > Radio gains a repeater toggle, 16 community-suggested radio
presets plus manual Freq/SF/BW/CR tuning (digit-by-digit Freq editor),
4 persisted user preset slots, and the packet pool bumped 16->32 so
queued retransmits stop starving incoming-packet allocation while
relaying.
Four opt-in politeness knobs (skip-advert, max-hops, yield, min-SNR),
all flood-only and off by default, plus overhear suppression that
cancels a queued retransmit if a peer relays the same packet first.
Adaptive Power Control is suppressed while relaying (pins TX power to
the ceiling) and duty-cycle RX is forced off, since a repeater needs
to hear and relay at consistent power.
A dedicated Tools > Repeater screen consolidates the toggle, the
politeness knobs, and live forwarding stats, plus an optional "Custom"
radio profile — a dedicated frequency/SF/BW/CR for relaying, separate
from the companion's own network, band-matched to the companion
frequency by default and used everywhere a radio change can happen
(boot, on-device toggle, app-driven CMD_SET_RADIO_PARAMS, Settings
radio edits) so the device never silently falls back to the wrong
params mid-relay.
Diagnostics gains the actually-forwarded packet count, real heap-free
via mallinfo(), a reset-counters popup, and hardened loop-detect
bounds. Also: a frequency-floor fix and a float-equality preset-match
fix in the repeater profile logic, deduped BW-table/valCol/profile-
seeding helpers shared between Settings and the Repeater screen, and
a build.sh fix tolerating control characters in `pio project config`'s
JSON dump.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Trail map dots/diamonds/cross/start markers and the north indicator were
drawn as raw unscaled pixels, so they shrank to near-invisible specks on
landscape e-ink's larger font scale; they now route through the mini-icon
framework (icons.h) like the rest of the UI, and the grid intersection dots
scale with it too. The keyboard's preview/grid separator had the same bug
(hardcoded 1px) and now uses display.sepH().
Also makes UP/DOWN (and the keyboard's LEFT/RIGHT/UP/DOWN) wrap top<->bottom
across every list, menu and form selector, matching the behavior PopupMenu
already had.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Fixes from a full ui-new audit (OLED + e-ink both build green):
- remove dead DisplayDriver::drawScrollArrows (all lists use drawScrollIndicator)
- SettingsScreen selection bar -> lineStep()-1, matching the drawList screens
- HomeScreen: don't force the 1s blink refresh on the CLOCK page (status icons
are hidden there anyway)
- FullscreenMsgView: clamp KEY_DOWN scroll to a cached _max_scroll instead of
over-incrementing and leaning on the next render to clamp
- DataStore: clamp use_lemon_font (>1 -> 0) on load, like the other enum fields
- move the ~1.5KB wrap scratch (trans/lines) off the render stack into shared
file-scope statics in FullscreenMsgView (single-threaded UI; the fullscreen
view and history list never lay out in the same frame)
Cleanup:
- drop dead members RingtoneEditorScreen::DUR_VALS and HomeScreen::sensors_scroll
- delete redundant manual scroll-clamps in handleInput across the drawList
screens (drawList already reclamps each render); remove the now-unused _visible
from QuickMsgScreen/NearbyScreen/BotScreen and BotScreen::scrollToSel()
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
- drawList(): scrollable list skeleton (visible window, keep-sel-in-view,
scroll-column reserve, per-row callback, indicator). Migrate Tools, Bot,
Nearby, Waypoints list and the three QuickMsg lists onto it; centralises the
scroll-clamp/reserve/indicator that each had open-coded (and inconsistently).
- drawCenteredHeader(): centred title + separator, replacing the duplicated
two-liner across ~10 screens (incl. QuickMsg, which used width()/2 spacing and
was missed before); unifies the separator at headerH()-sepH().
- keyIsPrev()/keyIsNext() in UIScreen.h for the LEFT||PREV / RIGHT||NEXT idiom;
applied to 6 screens, behaviour-preserving. Cancel/context-menu stay
per-screen (they mean different things on different screens).
- rotLabel() dedups the 0/90/180/270 array in Settings.
- Unify selection-row height to lineStep()-1 (Tools/Bot matched the rest).
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
- Replace single-letter M/B/A/G top-bar indicators with scalable mini-icons:
ICON_MUTE (speaker+cross), ICON_BLUETOOTH (rune), ICON_ADVERT (broadcast
mast+waves), ICON_TRAIL (map pin). Centred in the cw+2 indicator box;
disconnected BT shows the plain glyph instead of lowercase b.
- fix(settings): right-side values used display.valCol() without the scrollbar
reserve, so after expanding a section they rendered under the indicator.
Route all value cursors through valCol(display) = display.valCol() - _reserve.
- fix(settings): font toggle used ^=1, which on a stale value of 2 (older Hybrid
build) flips 2<->3 — both nonzero, locking applyFont() on Lemon with no way
back. Normalise: use_lemon_font = use_lemon_font ? 0 : 1.
- docs(settings): document Messages > Resend setting.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Replace the text ^/v scroll arrows with a font-scaling indicator drawn in
icons.h: a proportional thumb between fixed up/down triangle mini-icon caps.
drawScrollIndicator() lives in a ~5px right-edge column and scales via
miniIconScale (1x OLED, 2x landscape e-ink).
- Mini-icons: ICON_SCROLL_UP/DOWN; miniIconDrawTop (exact placement) and
miniIconDrawHalo (shape-hugging 1px DARK halo, clip_top to spare the header
separator) so caps stay visible on the LIGHT selection bar without a box.
- Thumb is 3*s wide so it centres on the triangle column; caps are static end
markers (always drawn) so neither vanishes at the extremes.
- scrollIndicatorReserve(): right-edge gutter (0 when the list fits). Content,
the selection bar and the message-history bubbles are all narrowed by it so
nothing renders under the scrollbar. Portrait e-ink wrap width subtracts the
reserve in both the box-height pass and render so wrapped text can't spill.
- Drop the redundant ">" selection marker (the highlight bar already shows
selection) and shift rows to x=2, reclaiming left-edge space.
- Wire the indicator into every scrollable list (Bot, Settings, Nearby, Tools,
Trail, QuickMsg lists + DM/channel history) and add one to WaypointsView,
which scrolled with no indicator before.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
End-to-end delivery indicators on the device UI, drawn next to outgoing
messages and auto-scaled to the font (legible on landscape e-ink).
DM (and room servers, which share the DM path):
- Pending / delivered / failed marker driven by the real end-to-end ACK.
Pending shows a row of dots — one per send — so auto-resend progress is
visible before it resolves to ✓ / ✗.
- Auto-resend: new pref dm_resend_count (0-5, default 2), Settings ›
Messages › Resend. A pending DM whose ACK times out is re-sent (reusing
the original timestamp) until resends run out, then ✗. Driven from
UITask::loop so it completes in the background, independent of screen.
- Incoming dedup: a retry reuses the sender timestamp + text but carries a
fresh packet hash, so addDMMsg drops copies matching prefix+ts+text.
Channels (flood, no recipient ACK):
- ✓ only once a repeater echo confirms the send was relayed into the mesh;
no echo is normal, not a failure (no pending/fail shown). A small ring
tracks a burst of sends so each matches its echo. Receive-path hashing is
gated so the hot flood path is untouched when idle.
Shared:
- Markers shown in both the history list and the fullscreen message view.
- Reusable scalable mini-icon facility in icons.h (bitmap + auto-scale);
adding a new status icon is a bitmap plus one draw call.
No changes to the upstream mesh library (src/).
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Pull repeated UI idioms into DisplayDriver and remove duplicated logic:
- DisplayDriver: add drawScrollArrows() and drawInvertedHeader(); replaces 11
copy-pasted scroll-arrow blocks across 5 screens and 3 inverted title-bar
blocks (NearbyScreen x2, NavView). Standardises the detail-view separator.
- useImperial(): single source on UITask; NearbyScreen/TrailScreen delegate
instead of each re-reading NodePrefs.units_imperial.
- NearbyScreen: extract saveSelectedWaypoint() (two identical blocks -> one);
drop the redundant local label buffer (WaypointStore truncates).
- UITask::shutdown(): power GPS off through LocationProvider::stop() instead of
poking PIN_GPS_EN directly — centralises enable/reset-pin + active-level logic.
Net -58 lines. Verified: GAT562 (SSD1306) and WioTrackerL1Eink (GxEPD) solo
builds compile clean.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Two independent, default-off toggles under Settings › Radio.
Pwr save: hardware RX duty-cycle (SX126x SetRxDutyCycle via
startReceiveDutyCycleAuto). The chip cycles RX↔sleep and wakes on a preamble —
no MCU state machine; recvRaw reads the packet exactly as in continuous RX.
Falls back to continuous RX on non-SX126x. (Replaces an earlier software-CAD
state machine that fought the hardware: polling a warm-sleeping chip gave a
phantom-busy channel that stalled TX ~4 s and dropped ACKs in the scan gaps.)
Auto pwr: Adaptive Power Control. tx_power_dbm becomes a ceiling; actual TX
power tracks the reverse-link SNR margin (measured above the per-SF demod floor,
EWMA-smoothed, proportional step with a deadband). Feedback comes from direct /
room-server ACKs and, for channels (no ACK), from hearing a repeater rebroadcast
our own flood; a lost confirmation ramps power back up so channel sends can't get
stranded below what the repeaters can hear.
Prefs schema 0xC0DE0009 (rx_powersave, tx_apc). Radio page / name bar show the
live TX power; noise floor reads n/a while duty-cycling.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
NearbyScreen:
- Hold Enter on a list row now shows Navigate and Save waypoint directly,
without entering the detail view first
- TIME added as the last filter slot (LEFT/RIGHT cycles Fav→ALL→…→Snsr→TIME);
time-sort shows age in right column and sorts by last-heard descending
- Save waypoint also available from detail view Options menu
UITask:
- Extract addWaypoint() helper (two overloads: with/without explicit timestamp)
consolidating the full()+add()+saveWaypoints()+alert pattern; TrailScreen
and QuickMsgScreen updated to use it
Fixes:
- SoundNotifier.h: correct NodePrefs.h include path (../NodePrefs.h)
- kbAddSensorPlaceholders: dereference _kb pointer in SettingsScreen,
QuickMsgScreen and BotScreen (signature changed to KeyboardWidget&)
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Moves KeyboardWidget from a per-screen value member to a single instance
owned by UITask, passed to SettingsScreen, QuickMsgScreen, and BotScreen
as a pointer. Only one screen is ever active at a time, so the shared
state is safe. Saves ~1.5 KB of always-resident heap.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
After widening the history buffers, the compose side was still the
bottleneck: the keyboard capped input at 139 bytes and the quick-message
expand buffers were 140. Raise KB_MAX_LEN to 160 (MeshCore's MAX_TEXT_LEN)
and size the expand/compose buffers to MSG_TEXT_BUF, so a message can be
typed, expanded, sent, stored and displayed at the full protocol length on
every path.
The custom-message editor now passes an explicit max bound to its 140-byte
store, so the wider keyboard buffer can't overflow it; the bot editor
already passed per-field maxima.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Add a single "Units" choice (Settings › System: Metric / Imperial) that
governs every distance and speed shown in Tools — Nearby Nodes, the Trail
views, and the navigate-to-point screen.
- NodePrefs: units_imperial (global) + trail_show_pace (Trail readout mode),
schema bumped 0xC0DE0005 → 0006. The old combined trail_units_idx is kept
for file-layout stability but no longer drives anything; upgraders default
to metric + speed.
- geo::fmtDist gains an imperial mode (ft below ~1000 ft, then miles).
- NavView / Nearby / Trail (waypoint list, Summary distance, List deltas,
map scale-bar label) all format through the global preference.
- Trail's action-menu "Units" row becomes a Speed/Pace readout toggle; the
km-vs-mi unit now follows the global setting instead of being one of four
combined options.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Add per-channel favourite marking and a Settings filter (all/fav) for
the channel list, symmetric with the existing DM and Room filters.
NodePrefs:
- ch_fav_bitmask (uint64_t): bit i = channel i is marked favourite
- ch_fav_only (uint8_t): 0=show all channels, 1=favourites only
- SCHEMA_SENTINEL bumped to 0xC0DE0005
DataStore: save/load both new fields before the sentinel.
SettingsScreen: new CH_FILTER item ('Channels: all/fav') in the
Contacts section, positioned between DM_FILTER and ROOM_FILTER.
QuickMsgScreen:
- buildChannelList() skips non-favourite channels when ch_fav_only=1
- Channel context menu gains a 4th option 'Fav'/'Unfav' that toggles
ch_fav_bitmask for the selected channel and rebuilds the list
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Previous fix only evicted SHUTDOWN when cur_len == PAGE_ORDER_LEN (full).
If the array was not yet full but had SHUTDOWN + 2 missing pages (TOOLS and
QUICK_MSG), TOOLS would fill the last slot but QUICK_MSG would be left out.
Remove the cur_len guard: evict SHUTDOWN whenever any required page is
missing, regardless of array fullness. This frees one slot before the
append loop so all missing required pages can be added in a single pass.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Previous fix appended missing pages only when there was room (cur_len <
PAGE_ORDER_LEN). On e-ink builds with GPS+SENSORS the default order fills
all 11 slots; old saves that included SHUTDOWN instead of TOOLS/QUICK_MSG
had no room to append the missing entries.
Now, if the array is full and a required page is absent, SHUTDOWN is evicted
first (it is appended at runtime by buildVisibleOrder's fallback and does not
need to be in the explicit list). This frees a slot for the missing page.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
ensurePageOrderInit returned early after inserting FAVOURITES without
checking whether TOOLS/QUICK_MSG were present. Old page_order saves that
predated those pages had CLOCK+FAVOURITES but no Messages entry, so
movePageInOrder always found cur==-1 and silently did nothing.
Now recount valid entries after any insertion, then walk the full list of
required page bits and append any that are absent (if room exists).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Earlier commits deleted the SECTION_GPS enum entry along with its only
remaining child (Trail dist moved to the Trail tool), but isSection()
and sectionName() still referenced it under the ENV_INCLUDE_GPS guard.
Both helpers no longer need a GPS case.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Per-tool config belongs in the tool, matching Auto-Advert's pattern.
SettingsScreen drops:
- TRAIL_MIN_DELTA enum entry + the entire SECTION_GPS gate (it was its
only remaining item after GPS upd / Trail int were removed)
- Render and input handler blocks
TrailScreen gains a small modal popup opened with Hold Enter (the
KEY_CONTEXT_MENU input). Enter cycles through the four min-dist values
(5/10/25/100 m), Esc closes the popup. The popup overlays whichever
view is active; savePrefs runs on each cycle so the value persists.
NodePrefs::trail_min_delta_idx and the TrailStore::MIN_DELTA_* helpers
are unchanged — only the entry point shifted.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
GPS NMEA polling is cheap, and a slower cadence just hides motion from
the trail; the min-delta gate already filters jitter without throttling
the GPS. Both knobs that exposed cadence-style controls to the user are
removed:
- Trail sampling is fixed at TrailStore::SAMPLING_SECS = 1 s, matching
the sensor manager's built-in GPS update default. The
intervalSecs / intervalLabel / INTERVAL_COUNT helpers go with it.
- GPS update rate ("GPS upd" entry) leaves the sensor manager on its
built-in 1 s default. applyGPSInterval and the GPS_INTERVAL_OPTS /
LABELS tables / gpsIntervalIndex helper are deleted.
Both NodePrefs fields (gps_interval, trail_interval_idx) are retained
as reserved so the schema sentinel doesn't have to bump — older saves
load cleanly, the bytes are just ignored.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Two new entries in the existing GPS section of SettingsScreen, gated by
the same ENV_INCLUDE_GPS guard. LEFT/RIGHT cycles through the option
table from Trail.h:
- "Trail int" : 30 s / 10 s / 20 s / 1 min / 5 min / 15 min
- "Trail dist": 5 m / 10 m / 25 m / 100 m
Changes are stored to p->trail_interval_idx / trail_min_delta_idx and
take effect on the next sampling tick in UITask::loop (already gated on
those fields), so no separate apply* helper is needed. _dirty triggers
the normal savePrefs on settings exit.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
ensurePageOrderInit only inserted FAVOURITES when len < PAGE_ORDER_LEN.
Older saves with all 11 slots filled (default order with GPS + SENSORS)
hit the full-array branch and were left without FAVOURITES in the
explicit order, so the page was shown via the missing-page fallback at
end of nav but movePageInOrder couldn't reorder it.
Now drop the last entry (typically SHUTDOWN, which the same fallback
already re-appends at end of nav) to make room. End result: FAVOURITES
sits after CLOCK, reorderable; nav layout matches the new default.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Render issues:
- Drop the "FAVOURITES" title — it overlapped the node-name/battery top
bar; the page-dots indicator already identifies the page
- Use the locally-computed content_y (matches other home pages) so tiles
sit below the dots row instead of starting at headerH() + sepH()
- Add 2 px top/bottom margin inside the grid so cells don't hug the dots
or the panel edge
Upgrade migration (visibility + position):
- Newly-loaded prefs with an older sentinel OR a non-default mask had
HP_FAVOURITES off and could not be enabled — DataStore::loadPrefsInt
now ORs HP_FAVOURITES into home_pages_mask whenever the sentinel
doesn't match the current schema
- Existing page_order_set users were stuck because FAVOURITES wasn't in
page_order, so movePageInOrder bailed — ensurePageOrderInit now
detects the missing FAVOURITES entry and inserts it right after CLOCK,
shifting the tail; if the array is already full the page still
appears via the buildVisibleOrder fallback
Bug fix in ensurePageOrderInit verification loop: iterated to HPB_COUNT
(12) over a PAGE_ORDER_LEN (11) array → one OOB read per call. Now
bounded to PAGE_ORDER_LEN.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
New home page rendering 6 pinned-contact slots. Grid transposes to
orientation: landscape → 3×2, portrait → 2×3. Joystick claims UP/DOWN
and inner LEFT/RIGHT for grid nav; edge LEFT/RIGHT fall through to
page navigation. Selected tile inverts via drawSelectionRow, filled
tile shows contact name + unread badge, empty tile shows "+".
Storage:
- NodePrefs::favourite_contacts[6][6] (6-byte pub_key prefix per slot,
all-zero = empty; collision probability with a real key is 2^-48)
- HomePageBit gains HPB_FAVOURITES = 11 (HPB_COUNT = 12), with a new
HP_FAVOURITES mask bit so the page is toggleable in Settings
- New PAGE_ORDER_LEN constant decouples the persisted array length (11)
from the page-type count; loops over page_order now use it, value-range
checks still use HPB_COUNT
- homePageBit returns 0 for HPB_SETTINGS / HPB_QUICK_MSG explicitly
rather than by bit-index range, so HPB_FAVOURITES (bit 11) is correctly
treated as toggleable
- Default order inserts FAVOURITES after CLOCK; SHUTDOWN drops to the
fallback "missing pages" append (still reachable, lands at end)
Schema sentinel bumped to 0xC0DE0002. DataStore::loadPrefsInt and
savePrefs read/write the new field. Older saves leave the field
zero-initialised (all slots empty), which is the natural starting state.
Phase 2 (Pin from Contact options) and Phase 3 (Pin from empty-slot
mini picker) wire interactions; this commit handles render + nav only.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
pageBit/bitToPage in HomeScreen and homePageBitIndex in SettingsScreen
each spelled out the bit assignment with magic numbers 0..10. Lift the
numbering into a NodePrefs::HomePageBit enum (HPB_CLOCK … HPB_QUICK_MSG,
HPB_COUNT) and route every reference through it: mapping functions, the
HP_* bitmasks, the homePageLabel table sizing, loop bounds over
page_order, the bounds check on page_order[0], the "always-visible"
discriminator for SETTINGS/QUICK_MSG.
Per-class enums (HomeScreen::HomePage, SettingsScreen::SettingItem)
stay — they index different concerns (navigation page vs. settings
row). The mapping functions still exist, but now reference a single
source of truth for the bit values.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Extends Features.h with preprocessor flags (FEAT_BRIGHTNESS_SETTING,
FEAT_CLOCK_SECONDS_SETTING, FEAT_DISPLAY_ROTATION_SETTING,
FEAT_JOYSTICK_ROTATION_SETTING, FEAT_FULL_REFRESH_SETTING) since
constexpr can't gate enum members or class fields. SettingsScreen.h
now uses #if FEAT_X instead of #if defined(EINK_DISPLAY_MODEL) — grep
on the feature name finds the toggle and every use site, and the
condition names *what* the gate controls.
Driver headers (DisplayDriver.h, GxEPDDisplay.h) keep raw
EINK_DISPLAY_MODEL — they're below the companion_radio layer and the
ifdef there gates on the build's panel type, not a UI feature.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Mechanical sweep across UITask.cpp and SettingsScreen.h. All current
format strings already fit their buffers, but a future format change
would silently overflow with sprintf. snprintf with sizeof makes the
buffer bound explicit and traceable to the array declaration.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Eight screens repeated the same if/else block to invert the row
background for selected items. Add DisplayDriver::drawSelectionRow that
sets LIGHT, optionally fills the rect, and leaves the colour as DARK
when sel (so the caller's text renders inverted). 61 lines removed
across SettingsScreen, KeyboardWidget (cells + special row), ToolsScreen,
DashboardConfigScreen, BotScreen, RingtoneEditorScreen (note slots +
menu), NearbyScreen, QuickMsgScreen (4 list views).
Card-style rows (QuickMsg hist, NearbyScreen discover, RingtoneEditor
notes display) keep their original drawRect/partial-fill outline for
unselected — they don't match the simple-invert pattern.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Previously page_order_set status was inferred from page_order[0] being
in 1..11, so a single junk byte in that range falsely triggered
custom-order mode. Add explicit page_order_set magic (0xA5) written
alongside the array; pre-magic saves are migrated once on load when
their first byte still passes the legacy range check.
Also fix(ui): keep "@[nick] " prefix out of placeholder expansion in
QuickMsgScreen reply path, so a nick containing a token like {loc}
isn't substituted.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add "Full rfsh" setting (e-ink only) with options off/5/10/20/30
partial refreshes between full refreshes. Prevents ghosting on panels
that accumulate artifacts after many partial updates.
GxEPDDisplay counts partial refreshes and calls display.display(false)
every N frames when the interval is set. Persisted in DataStore and
applied at startup via applyFullRefreshInterval().
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
ensurePageOrderInit now scans for CLOCK (bit 0, stored as 1) after the
existing page_order[0] validity check — if Clock is absent (partial or
corrupted saved order), it resets the array and re-initialises all pages.
renderItem calls ensurePageOrderInit before displaying home page positions
so that position numbers appear immediately on entering Settings rather
than only after the first reorder action.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- home_pages_mask XOR toggle initialises to HP_ALL before flipping bit,
preventing accidental hiding of all other pages when mask starts at 0
- buildVisibleOrder appends any visible page missing from custom page_order,
so pages absent from migrated/corrupted prefs remain navigable
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add NodePrefs::joystick_rotation (0-3 steps CW), persisted in DataStore
alongside display_rotation. rotateJoystickKey() now takes a runtime rot
parameter instead of compile-time JOYSTICK_ROTATION macro. UITask::loop()
reads joystick_rotation from NodePrefs each frame. Settings screen exposes
"Joystick" rotation item on any build with UI_HAS_JOYSTICK. JOYSTICK_ROTATION
macro still works as compile-time default for legacy/non-prefs builds.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Column at width()-6*charWidth so "always" touches the right edge;
ON and OFF start at the same x position.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Use %2d (right-aligned, always 3 chars) instead of %d so label x-position
stays constant when going from single-digit (1-9) to double-digit (10-11).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Resolved conflicts to preserve eink-ui layout helpers (valCol, lineStep, sepH)
while integrating the page_order persistence, buildVisibleOrder(), and
Settings/Messages ordering UI from the wio-tracker-l1-improvements branch.
display_rotation is now written before page_order in the save/load sequence.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
MarekZegare4andClaude Opus 4.8
JakubandClaude Sonnet 4.6
vanous